Simpson Strong-Tie

The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the...

The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. Using a BP58-2 bearing plate installed in the seat of the HTT5 provides add more allowable tension load to the connection. HTT5 Tension Ties are designed to be used in both in vertical and...

The Simpson CBSQ88-SDS2 (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post...

The Simpson CBSQ88-SDS2 (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 8 x 8 Nominal (7-1/2" x 7-1/2") Base: 12 Ga. (7-1/2" x 7-3/8") Strap: 8 Ga. x 3" Wide x 8-11/16" High CBSQ88 Information and Installation...

The Simpson BC8 Post Caps allow you to create a light duty connection between a 8 x 8 nominal post and 8x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 7-1/2" (W) x 7-1/2" (L)...

The Simpson BC8 Post Caps allow you to create a light duty connection between a 8 x 8 nominal post and 8x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 7-1/2" (W) x 7-1/2" (L) Fastener Options: (24) 16d BC8 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...

The Simpson Strong-Tie Deck Drive™ DSVR3S #10 x 3" Red Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start...

The Simpson Strong-Tie Deck Drive™ DSVR3S #10 x 3" Red Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVR3S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber so...

The Simpson Strong-Tie LS90Z ZMax® Coated Skewable Reinforcing Angles are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only...

The Simpson Strong-Tie LS90Z ZMax® Coated Skewable Reinforcing Angles are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time. Flanges are 2-1/4" wide. LS90Z Angles can use 10d .148" x 1-1/2" or longer nails depending on the application. Material: 18 Gauge Finish: ZMax® Coating Galvanizing Length: 7-7/8" Flange Widths: 2-1/4" x 2-1/4" Fasteners: (12) 10d x 1-1/2" Nails LS90Z Information and...

Simpson Strong Drive® SSNS10D5 1-1/2" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required...

Simpson Strong Drive® SSNS10D5 1-1/2" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 600 nails per 5lb pack. The nails are stainless steel providing high/severe corrosion protection. SSNA10D5 Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel chromium...

The 1-1/4" wide x 18" long LTS18SS Stainless Steel Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss...

The 1-1/4" wide x 18" long LTS18SS Stainless Steel Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. LTS18SS straps should be used where severe corrosive conditions exist. Material: 18 gauge Finish: Stainless Steel Dimensions: 1-1/4" (Wide) x 18" (Length) Fasteners: 10d or...

Simpson Strong-Tie HDU8-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come...

Simpson Strong-Tie HDU8-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (20) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Hot Dipped Galvanized holdowns should be used when the application in...

The Simpson Strong-Tie 2-5/16" x 20" MIT3520 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...

The Simpson Strong-Tie 2-5/16" x 20" MIT3520 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90 Galvanized...

The Simpson Strong-Tie Deck Drive™ DSVT212S #10 x 2-1/2" Tan Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...

The Simpson Strong-Tie Deck Drive™ DSVT212S #10 x 2-1/2" Tan Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVT212S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth...

The Simpson Strong-Tie LPC4Z design allows you the flexibility to connect a 4x or smaller width beam or joist to the top of a 4x post. Sold By Each Material: 18 Gauge Post Width: 3-1/2" Finish:...

The Simpson Strong-Tie LPC4Z design allows you the flexibility to connect a 4x or smaller width beam or joist to the top of a 4x post. Sold By Each Material: 18 Gauge Post Width: 3-1/2" Finish: ZMax® G-185 Galvanized Fasteners: (8) 10d (Beam) , (8) 10d (Post) LPC4Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating) than the standard hot-dip galvanized coating (galvanized...

Simpson Strong-Tie ITS2.06/16 sets a new standard for engineered wood top flange hangers. The ITS2.06/16 installs 2" or 2-1/16" x 16" I-Joists faster and uses less nails than any other EWP top...

Simpson Strong-Tie ITS2.06/16 sets a new standard for engineered wood top flange hangers. The ITS2.06/16 installs 2" or 2-1/16" x 16" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the...

The Simpson CBSQ88-SDS2HDG Hot Dipped Galvanized (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1"...

The Simpson CBSQ88-SDS2HDG Hot Dipped Galvanized (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Hot Dipped Galvanizing provides added corrosion protection Easier Installation Higher Loads Hot Dipped Galvanized Column Size: 8 x 8 Nominal (7-1/2" x 7-1/2") Base: 12 Ga. (7-1/2" x 7-3/8")...

The Simpson Strong-Tie SUL210 Skewed Left 2 x 10/12 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate...

The Simpson Strong-Tie SUL210 Skewed Left 2 x 10/12 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8" (Outside Flange) x 1-5/16" (Inside Flange) Fastener Options : (10) .162 x 3-1/2" 16d Nails (Face) (10) .148...

Simpson Strong-Tie CS16-R 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16-R are approved for use with SD Screws as a nail...

Simpson Strong-Tie CS16-R 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16-R are approved for use with SD Screws as a nail substitution. 25' packs are an economical choice when you do not require large amounts. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 25' (Length) Fasteners: 8d or 10d depending on end length and material (See link below for more information) CS16-R Information and...

Simpson Strong-Tie P27SL4 Yellow Powder Strip Loads fit many of following tools: Simpson: PTP-27, PTP-27AL, PTP-27ALMAGR, PTP-27AS, PTP-27AS, PTP-27ASMAGR, PTM-27, PTM-27HD, PT-27 Others: DX-350,...

Simpson Strong-Tie P27SL4 Yellow Powder Strip Loads fit many of following tools: Simpson: PTP-27, PTP-27AL, PTP-27ALMAGR, PTP-27AS, PTP-27AS, PTP-27ASMAGR, PTM-27, PTM-27HD, PT-27 Others: DX-350, DX351, DX36, DX-A40, DX-A41 (except P27SL3), DX-450, DX-451, System 1H, P-368, A-40B, A-41B, Cobra, and most .27 caliber clone tools. P27SL Series SDS Sheet Please Note: Due to shipping restrictions on powder loads we can only ship theses loads by Ground Shipping to the 48 continental states....

The Simpson Strong-Drive® SDS25412 1/4" x 4-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25412 screw...

The Simpson Strong-Drive® SDS25412 1/4" x 4-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25412 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 4-1/2" Thread Length: 2-3/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive...

Simpson Strong-Tie CCO8 End Column Caps with no post straps provides a high capacity connection between a 8x wide beam and a steel post. The CCO8 Column Caps comes with no coating to allow you to...

Simpson Strong-Tie CCO8 End Column Caps with no post straps provides a high capacity connection between a 8x wide beam and a steel post. The CCO8 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 7-1/2" (Beam) x 13"...

Simpson Strong-Tie ECC68 End Column Caps provide a high capacity connection between a 6x beam and a 8x post. ECC68 End Column Caps should be used when the 6x beam ends at the 8x post. Please Note:...

Simpson Strong-Tie ECC68 End Column Caps provide a high capacity connection between a 6x beam and a 8x post. ECC68 End Column Caps should be used when the 6x beam ends at the 8x post. Please Note: This column cap is also available in powder coat or Hot Dipped Galvanized as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/2" (Beam) x 7-1/2" (Post) x 9-1/2" (Length) Fasteners: (2) 5/8"...

Simpson Strong Tie HGUS412 4 x 12 Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge...

Simpson Strong Tie HGUS412 4 x 12 Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-5/8" (Wide) x 10-7/16" (Height) x 4" (Seat Depth) Fastener Options: (56) 16d Nails (Header) (20) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS412 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...

Simpson Strong-Tie IUS2.37/9.5 is used to install 2-5/16" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...

Simpson Strong-Tie IUS2.37/9.5 is used to install 2-5/16" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-7/16" (Wide) x 9-1/2" (Height) x 2" (Seat Depth) Fastener Options : (8) .148 x 3" Nails (Face) IUS2.37/9.5 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...

Simpson Strong Drive® SSNS10DB 1-1/2" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required...

Simpson Strong Drive® SSNS10DB 1-1/2" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 3000 nails per 25 lb. bucket. The nails are stainless steel providing high/severe corrosion protection. SSNA10DB Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel chromium...

The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...

The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...

Simpson Strong Tie HUC28-2Z ZMax® Double 2 x 8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use...

Simpson Strong Tie HUC28-2Z ZMax® Double 2 x 8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC28-2Z ZMax® hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will...