Concrete Forming Supplies

The 4" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the...

The 4" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 4" Bar Ties Various Rebar Combinations: #2 Bar (1/4") to #3 Bar (3/8") Explanation of "Stock"...

CWC 135-072 #18 x 550' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend,...

CWC 135-072 #18 x 550' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend, lower stress point than braided seine twine. Ties easily and knots securely. Common to the marine, electrical and construction industries, this twine is also useful in home and garden applications. Resists abrasion, mildew and most chemicals Used for chalk line, fishing line and net repair #18 Size...

FASTFOOT® FF50 Fabric Forms eliminated the use of heavy dimensional lumber and plywood when forming footing 18" wide by 10" deep or less. Because of the speed of preparation and tear down the...

FASTFOOT® FF50 Fabric Forms eliminated the use of heavy dimensional lumber and plywood when forming footing 18" wide by 10" deep or less. Because of the speed of preparation and tear down the FASTFOOT® system offers a great labor savings. Prevents Concrete Damage - Fastfoot® is a closed form. There is no concrete damage to screed boards and stakes. This means your 2x4s and stakes can be re-used indefinitely. Adapts to Uneven Ground, Rock - Special colored width lines allow...

OCM 2" or 2-1/4" PCC2.00-2.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation....

OCM 2" or 2-1/4" PCC2.00-2.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 3-1/2" base diameter Fits up to #8 rebar Will not puncture...

OCM, Inc #STSEC-6HH 6" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining...

OCM, Inc #STSEC-6HH 6" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 6" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 6" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...

Simpson Strong Tie AnchorMate® 5/8" Anchor Bolt Holders are designed to hold 5/8" anchor bolts including SSTB Bolts in place before the concrete pour. With a unique grip placed properly there is...

Simpson Strong Tie AnchorMate® 5/8" Anchor Bolt Holders are designed to hold 5/8" anchor bolts including SSTB Bolts in place before the concrete pour. With a unique grip placed properly there is no need for a hex nut during the pour. Additionally and Anchormate® protects the threads from splashed concrete. Built-in 2x4 and 2x6 stops eliminate measuring. Elevated bolt grippers allow easy trowel finishing. Color-coded for easy size identification. Lightweight, durable and easy to use....

The Simpson Strong-Tie WT-6 Wedge Form Ties are designed for low foundation wall applications with a 6" width. Their 5/8" wide formed "V" design for rigidity allows accurate form spacing and...

The Simpson Strong-Tie WT-6 Wedge Form Ties are designed for low foundation wall applications with a 6" width. Their 5/8" wide formed "V" design for rigidity allows accurate form spacing and support. Material: 14 Gauge Galvanized Use two 3-1/2" long wedges for each tie. Not recommended for wall pours greater than 4' high. Wall thickness from 6". Refer to technical bulletin T-WT for recommended spacing. Please Note: Wedges are sold separately. Explanation of "Stock" Availability Term Stock...

The 6" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the...

The 6" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 6" Bar Ties Various Rebar Combinations: #4 Bar (1/2") to #6 Bar (3/4") #5 Bar (5/8") to #5...

CWC 135-127 #18 x 1,100' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend,...

CWC 135-127 #18 x 1,100' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend, lower stress point than braided seine twine. Ties easily and knots securely. Common to the marine, electrical and construction industries, this twine is also useful in home and garden applications. Resists abrasion, mildew and most chemicals Used for chalk line, fishing line and net repair #18 Size...

FASTFOOT® FF50-C 18" Sewn Corners are the perfect accessory to the 18" FASTFOOT® Footing on a roll. Using these sewn corners means no cutting and can easily be installed by one person. The...

FASTFOOT® FF50-C 18" Sewn Corners are the perfect accessory to the 18" FASTFOOT® Footing on a roll. Using these sewn corners means no cutting and can easily be installed by one person. The FASTFOOT® Corners are 4' x 4' giving you approximately 6 lineal feet of forms when figuring in the over lap. Forms 90° corners Saves time and labor No required cutting Explanation of "Stock" Availability Term Stock items are products we normally have available for immediate shipment either...

OCM, Inc #STLEC-6HH 6" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard...

OCM, Inc #STLEC-6HH 6" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties use...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 7-5/8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 7-5/8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...

The 8" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the...

The 8" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 8" Bar Ties Various Rebar Combinations: #4 Bar (1/2") to #10 Bar (1-1/4") #5 Bar (5/8") to #8...

OCM 3" or 3-1/4" PCC3.00-3.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation....

OCM 3" or 3-1/4" PCC3.00-3.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 4-1/8" base diameter Fits up to #8 rebar Will not puncture...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 8" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a...

The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 8" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...