Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson Strong-Tie DSC2L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are...
The Simpson Strong-Tie DSC2L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. Material: 7 gauge Finish: Standard G90 Galvanized Dimensions: 16" (Length) x 3" (Flanges) Included Fasteners: (20) SDS 1/4" x 3" DSC2L-SDS3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...
The Simpson Strong-Tie H1A Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1A is designed for nominal 2x...
The Simpson Strong-Tie H1A Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1A is designed for nominal 2x lumber. These U-shaped hurricane ties provide faster installation than using two single-sided ties. The embossments add stiffness in crucial areas for improved performance. Holds the rafter or truss on both sides for high lateral load resistance Can be installed on inside or outside of wall, or...
The Simpson Strong-Tie HGA10 Gusset Angle w/SDS Screws attaches to the top plate and gable trusses or rim joist to provides good lateral (cross) wind resistance. Each Bracket Includes: (4) 1/4" x...
The Simpson Strong-Tie HGA10 Gusset Angle w/SDS Screws attaches to the top plate and gable trusses or rim joist to provides good lateral (cross) wind resistance. Each Bracket Includes: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws Material: 14 Gauge Finish: Standard G90 Zinc Fastener Included: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws HGA10 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move...
The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...
The Simpson Strong-Tie VPA2 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 1-1/2" wide rafters to the top plate. It will adjust to accommodate...
The Simpson Strong-Tie VPA2 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 1-1/2" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 1-9/16" Actual Joist Width: 1-1/2"...
The Simpson Strong-Tie DSC2R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that...
The Simpson Strong-Tie DSC2R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. Material: 7 gauge Finish: Standard G90 Galvanized Dimensions: 16" (Length) x 3" (Flanges) Included Fasteners: (20) SDS 1/4" x 3" DSC2R-SDS3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1A Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic...
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1A Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1A is designed for nominal 2x lumber. These U-shaped hurricane ties provide faster installation than using two single-sided ties. The embossments add stiffness in crucial areas for improved performance. Holds the rafter or truss on both sides for high lateral load resistance Can be...
The Simpson Strong-Tie HGA10HDG Hot Dipped Galvanized Gusset Angle w/SDS Screws attaches to the top plate and gable trusses or rim joist to provides good lateral (cross) wind resistance. Use Hot...
The Simpson Strong-Tie HGA10HDG Hot Dipped Galvanized Gusset Angle w/SDS Screws attaches to the top plate and gable trusses or rim joist to provides good lateral (cross) wind resistance. Use Hot Dipped Galvanized HGA10 angles when you need additional corrosion protection. Includes: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws. Material: 14 Gauge Finish: Hot Dipped Galvanized/li> Fasteners included: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws HGA10HDG Information and...
Save by Purchasing 48 Box Special! The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will...
Save by Purchasing 48 Box Special! The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of...
The Simpson Strong-Tie VPA25 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 1-3/4" wide rafters to the top plate. It will adjust to accommodate...
The Simpson Strong-Tie VPA25 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 1-3/4" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 1-13/16" Actual Joist Width: 1-3/4"...
The Simpson Strong-Tie DSC5L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are...
The Simpson Strong-Tie DSC5L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5L-SDS3 series drag strut connectors requires 40% less fasteners than the DSC4L connector but gets 12% higher loads. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS 1/4" x 3" DSC5L-SDS3...
The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to...
The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...