Login/Register
Shopping Cart
OR
Filter
Sort By
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1AZ Zmax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind...
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1AZ Zmax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1A is designed for nominal 2x lumber. These U-shaped hurricane ties provide faster installation than using two single-sided ties. The embossments add stiffness in crucial areas for improved performance. Holds the rafter or truss on both sides for high lateral load resistance...
The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases...
The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases strength for lateral and uplift loads. This hurricane gusset angle installs easily with 1 1/2" Strong-Drive® SDS Heavy-Duty Connector screws and Titen Turbo™ masonry screws to concrete or masonry. Each Kit Includes: (10) HGAM Hurricane Gusset Angles (40) 1/4" x 1-1/2" SDS Screws and (40)...
The Simpson Strong-Tie VPA2.1 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/16" wide rafters to the top plate. It will adjust to accommodate...
The Simpson Strong-Tie VPA2.1 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/16" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-1/8" Actual Joist Width:...
The Simpson Strong-Tie DSC5R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that...
The Simpson Strong-Tie DSC5R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5R-SDS3 drag strut connectors requires 40% less fasteners than the DSC4R connector but gets 12% higher loads. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS 1/4" x 3" DSC5R-SDS3...
The Simpson Strong-Tie H1.81Z ZMax® Hurricane Tie is designed for use with 1 3/4" LVL roof rafters to provide a stronger connection to the top plate of the wall. It's ideal for connections when...
The Simpson Strong-Tie H1.81Z ZMax® Hurricane Tie is designed for use with 1 3/4" LVL roof rafters to provide a stronger connection to the top plate of the wall. It's ideal for connections when there are higher-load demands on the structure, like a heavy snow load, and provides lateral resistance in a seismic event. This 1 3/4"-wide H1.81Z connector is the first hurricane tie to be specifically sized for engineered wood. The H1.81Z installs with half the nails that are needed for two...
The Simpson Strong-Tie STCT Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. Use STCT clips where truss and rafter are separated from the top plate of the...
The Simpson Strong-Tie STCT Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. Use STCT clips where truss and rafter are separated from the top plate of the non-bearing wall. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STCT Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides)....
The Simpson Strong-Tie VPA35 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/4" or 2-5/16" wide rafters to the top plate. It will adjust to...
The Simpson Strong-Tie VPA35 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/4" or 2-5/16" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-5/16" Actual Joist...
The Simpson Strong-Tie DSC5R-SDS3HDG Hot Dipped Galvanized Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed...
The Simpson Strong-Tie DSC5R-SDS3HDG Hot Dipped Galvanized Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5R-SDS3 series drag strut connectors requires 40% less fasteners than the DSC4L connector but gets 12% higher loads. Material: 3 gauge Finish: Hot Dipped Galvanized Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS...
The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip...
The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (10) 8d x 1-1/2" Nails or (10) SD9 x 1-1/2" Screws H2.5A Information and Installation Instructions. Standard G90 Zinc Galvanized...
The Simpson Strong-Tie VPA3 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/2" or 2-9/16" wide rafters to the top plate. It will adjust to...
The Simpson Strong-Tie VPA3 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/2" or 2-9/16" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-9/16" Actual Joist...
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top...
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (10) 8d x 1-1/2" Nails or (10) SD9 x 1-1/2" Screws H2.5A Information and Installation...
The Simpson Strong-Tie HTC4 Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The HTC4 has three 2-1/2" slots that will permit the truss chord...
The Simpson Strong-Tie HTC4 Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The HTC4 has three 2-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. This connector has high lateral capacity and can be used on 2 x 4 and 2 x 6 top plates Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (9) .148 x 3" Nails HTC4 Information and Installation Instructions Standard G90 Zinc Galvanized...
The Simpson Strong-Tie VPA4 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 3-1/2" wide rafters to the top plate. It will adjust to accommodate...
The Simpson Strong-Tie VPA4 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 3-1/2" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 3-9/16" Actual Joist Width: 3-1/2"...
The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate...
The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H2.5AZ Information and Installation...
The Simpson Strong-Tie TBE4 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 4 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It...
The Simpson Strong-Tie TBE4 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 4 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It replaces nail-on scabs that provide lower load transfer, or in some cases, an additional ply when needed for bearing. One size works with any number of girder plies. Must be used in pairs Material: 18 Gauge Finish: Standard G90 Zinc Width: 3-9/16" Fasteners (Rafter): (10) .148 x 1-1/2" Nails (Single Truss...
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A...
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2"...