Roof Truss Clips

The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move...

The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...

Save by Purchasing 48 Box Special! The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will...

Save by Purchasing 48 Box Special! The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of...

The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to...

The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots...

Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating...

The Simpson Strong-Tie STCT Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. Use STCT clips where truss and rafter are separated from the top plate of the...

The Simpson Strong-Tie STCT Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. Use STCT clips where truss and rafter are separated from the top plate of the non-bearing wall. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STCT Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides)....

The Simpson Strong-Tie HTC4 Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The HTC4 has three 2-1/2" slots that will permit the truss chord...

The Simpson Strong-Tie HTC4 Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The HTC4 has three 2-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. This connector has high lateral capacity and can be used on 2 x 4 and 2 x 6 top plates Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (9) .148 x 3" Nails HTC4 Information and Installation Instructions Standard G90 Zinc Galvanized...

The Simpson Strong-Tie TBE4 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 4 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It...

The Simpson Strong-Tie TBE4 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 4 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It replaces nail-on scabs that provide lower load transfer, or in some cases, an additional ply when needed for bearing. One size works with any number of girder plies. Must be used in pairs Material: 18 Gauge Finish: Standard G90 Zinc Width: 3-9/16" Fasteners (Rafter): (10) .148 x 1-1/2" Nails (Single Truss...

The Simpson Strong-Tie TBE6 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 6 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It...

The Simpson Strong-Tie TBE6 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 6 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It replaces nail-on scabs that provide lower load transfer, or in some cases, an additional ply when needed for bearing. One size works with any number of girder plies. Must be used in pairs Material: 18 Gauge Finish: Standard G90 Zinc Width: 5-9/16" Fasteners (Rafter): (10) .148 x 1-1/2" Nails (Single Truss...

The Simpson Strong-Tie VTCR Single-Sided Valley Truss Clip provides a positive connection between the valley truss and the supporting framing below. Installed on top of the roof sheathing, it...

The Simpson Strong-Tie VTCR Single-Sided Valley Truss Clip provides a positive connection between the valley truss and the supporting framing below. Installed on top of the roof sheathing, it eliminates the need to add a support wedge under the valley truss or to bevel the bottom chord to match the roof pitch. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-1/2" Fasteners (Supporting Frame): (4) .148 x 3" Nails or (4) SD9212 Structural Screws Fasteners (Valley Truss): (3) .148 x 3" Nails...