Products 1-24 of 32
Show
Availability: Stock
Simpson Strong-Tie
Item #: H1 -
The Simpson Strong-Tie H1 Hurricane and Seismic Ties are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Ships Free!
Availability: Stock
Simpson Strong-Tie
Item #: H1-48 -
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1 Hurricane and Seismic Ties are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...
Availability: Stock
Simpson Strong-Tie
Item #: H1Z -
The Simpson Strong-Tie H1Z Hurricane Ties with ZMax® Corrosion Resistance are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1Z Information and Installation Instructions. ZMax® Galvanized Coating Information...
Availability: Stock
Simpson Strong-Tie
Item #: H1.81Z -
The Simpson Strong-Tie H1.81Z ZMax® Hurricane Tie is designed for use with 1 3/4" LVL roof rafters to provide a stronger connection to the top plate of the wall. It's ideal for connections when there are higher-load demands on the structure, like a heavy snow load, and provides lateral resistance in a seismic event. This 1 3/4"-wide H1.81Z connector is the first hurricane tie to be specifically sized for engineered wood. The H1.81Z installs with half the nails that are needed for two...
Availability: Stock
Simpson Strong-Tie
Item #: H2.5A -
The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (10) 8d x 1-1/2" Nails or (10) SD9 x 1-1/2" Screws H2.5A Information and Installation Instructions. Standard G90 Zinc Galvanized...
Ships Free!
Availability: Stock
Simpson Strong-Tie
Item #: H2.5A-72 -
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (10) 8d x 1-1/2" Nails or (10) SD9 x 1-1/2" Screws H2.5A Information and Installation...
Availability: Stock
Simpson Strong-Tie
Item #: H2.5AZ -
The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H2.5AZ Information and Installation...
Ships Free!
Availability: Stock
Simpson Strong-Tie
Item #: H2.5AZ-72 -
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2"...
Availability: Stock
Simpson Strong-Tie
Item #: H2.5ASS -
The Simpson Strong-Tie H2.5ASS Ties with 316L Stainless Steel Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5ASS Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. Material: 18 Gauge Finish: Type 316L Stainless Steel Fasteners: (10) 8d x 1-1/2" Nails H2.5ASS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L...
Availability: Stock
Simpson Strong-Tie
Item #: H2A -
The Simpson Strong-Tie H2A Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2A installation ties the rafter to the stud while spanning a top plate. The Simpson H2A requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (12) 8d x 1-1/2" Nails H2A Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Availability: Stock
Simpson Strong-Tie
Item #: H2AZ -
The Simpson Strong-Tie H2AZ ZMax® Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2AZ installation ties the rafter to the stud while spanning a top plate. The Simpson H2AZ requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (12) 8d x 1-1/2" Nails H2AZ Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating...
Availability: Stock
Simpson Strong-Tie
Item #: H3 -
The Simpson Strong-Tie H3 Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3 installation ties the single top plate to the rafter or truss. The Simpson H3 requires (8) 8d joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (8) 8d x 2-1/2" Nails H3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
Ships Free!
Availability: Stock
Simpson Strong-Tie
Item #: H3-72 -
Save by Purchasing a Pallet of 72 Boxes! The Simpson Strong-Tie H3 Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3 installation ties the single top plate to the rafter or truss. The Simpson H3 requires (8) 8d joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (8) 8d x 2-1/2" Nails H3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...
Availability: Stock
Simpson Strong-Tie
Item #: H3Z -
The Simpson Strong-Tie H3Z Clip with ZMax® Corrosion resistance is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3Z installation ties the single top plate to the rafter or truss. The Simpson H3Z requires (8) 8d joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (8) 8d x 2-1/2" Nails H3Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax®...
Availability: Stock
Simpson Strong-Tie
Item #: H6 -
Simpson Strong-Tie H6 Hurricane Tie are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6 Tie requires (16) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: Standard G90 Zinc Fastener Options: (16) 8d x 1-1/2" Nails H6 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This...
Availability: Stock
Simpson Strong-Tie
Item #: H6Z -
Simpson Strong-Tie H6Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6Z Tie requires (16) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (16) 8d x 1-1/2" Nails H6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a...
Availability: Stock
Simpson Strong-Tie
Item #: H7Z -
Simpson Strong-Tie H7Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to both the top plate and rafter. The H7Z Tie requires (14) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (14) 8d x 1-1/2" Nails H7Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating)...
Availability: Stock
Simpson Strong-Tie
Item #: H8 -
Simpson Strong-Tie H8 Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8 Hurricane Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: Standard G90 Zinc Coating Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
Availability: Stock
Simpson Strong-Tie
Item #: H8Z -
Simpson Strong-Tie H8Z ZMax® Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8Z Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per...
Availability: Stock
Simpson Strong-Tie
Item #: H8SS -
Simpson Strong-Tie H8SS Type 316L Stainless Steel Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8SS Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: Type 316L Stainless Steel Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8SS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L stainless steel is...
Availability: Stock
Simpson Strong-Tie
Item #: H10A -
Simpson Strong-Tie H10A Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10A can also be field-bent to connect to shear blocking as well. The H10A uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10A Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...
Availability: Stock
Simpson Strong-Tie
Item #: H10AZ -
Simpson Strong-Tie H10AZ with ZMax® Corrosion Protection Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10AZ can also be field-bent to connect to shear blocking as well. The H10AZ uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (18) 10d .148" x 1-1/2" H10A Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM...
Availability: Stock
Simpson Strong-Tie
Item #: H10ASS -
Simpson Strong-Tie H10ASS with Type 316L Corrosion Protection Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10ASS can also be field-bent to connect to shear blocking as well. The H10AZ uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Type 316L Stainless Steel Fastener Options: (18) 10d .148" x 1-1/2" H10ASS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L stainless steel is a nickel-chromium...
Availability: Stock
Simpson Strong-Tie
Item #: H10AR -
Simpson Strong-Tie H10AR Hurricane Tie for connection a double top plate to a 2x rough sawn rafter or truss. The H10AR can also be field-bent to connect to shear blocking as well. The H10AR uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10AR Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of...