Login/Register
Shopping Cart
OR
Filter
Sort By
Simpson Strong Tie HUS1.81/10 1-3/4" x 9" Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...
Simpson Strong Tie HUS1.81/10 1-3/4" x 9" Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-13/16" (Wide) x 8-7/8" (Height) x 3" (Seat Depth) Fastener Options: (30) 16d Nails or SD10212 Screws(Header) (10) 16d Nails...
The Simpson Strong-Tie CJT3ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...
The Simpson Strong-Tie CJT3ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT3ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 6 Glulam Beam - 3-1/8" x 7-1/2" PSL - 3-1/2 x...
The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...
The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...
Simpson Strong Tie HGUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge...
Simpson Strong Tie HGUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 5-3/8" (Height) x 5" (Seat Depth) Fastener Options: (20) 16d Nails (Header) (8) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS26 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...
Simpson Strong-Tie HTU26 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26 hanger very versatile for various...
Simpson Strong-Tie HTU26 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26 hanger very versatile for various trusses. Additionally you can have the HTU26 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is 1/8" per ASTM...
Simpson Strong Tie face mount HU1.81/5 Composite Lumber Hanger is designed for hanging 1-3/4" x 5-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load...
Simpson Strong Tie face mount HU1.81/5 Composite Lumber Hanger is designed for hanging 1-3/4" x 5-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 5-3/8" (Height) x 2-1/2" (Seat Depth) Fastener Options: (12) 16d Nails (Header-Min) (4) 10d Nails (Joist-Min) (16) 16d Nails (Header-Max) (6) 10d Nails (Joist-Max) HU1.81/5 Information and Installation...
Simpson Strong Tie HU24-2 Double 2 x 4 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HU24-2 Double 2 x 4 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 3-1/16" (Height) x 2-1/2" (Seat Depth) Fastener Options: (4) .162 x 3-1/2" (16d) Nails (Header) (2) .148 x 3" (10d) Nails (Joist) HU24-2 Information and...
Simpson Strong Tie HUCQ1.81/9-SDS 1-3/4" Wide x 9" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/9-SDS hangers with concealed...
Simpson Strong Tie HUCQ1.81/9-SDS 1-3/4" Wide x 9" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/9-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-3/4" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (8) SDS 1/4" x 1-3/4" Screws (Header) (4) SDS 1/4" x 1-3/4" Screws...
Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...
Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS26 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 5-3/8" (Height) x 3" (Seat Depth)...
Simpson Strong-Tie ITS1.56/11.88 sets a new standard for engineered wood top flange hangers. The ITS1.56/11.88 installs 1-1/2" x 11-7/8" I-Joists faster and uses less nails than any other EWP top...
Simpson Strong-Tie ITS1.56/11.88 sets a new standard for engineered wood top flange hangers. The ITS1.56/11.88 installs 1-1/2" x 11-7/8" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Material: 18 gauge Finish: Standard G90...
Simpson Strong-Tie IUS1.81/9.5 is used to install 1-3/4" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...
Simpson Strong-Tie IUS1.81/9.5 is used to install 1-3/4" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-7/8" (Wide) x 9-1/2" (Height) x 2" (Seat Depth) Fastener Options : (8) .148 x 3" Nails (Face) IUS1.81/9.5 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
The Simpson Strong-Tie LSSJ26LZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 6 jack rafters to hip/valley members when the rafter skews to the left. Its simple design makes...
The Simpson Strong-Tie LSSJ26LZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 6 jack rafters to hip/valley members when the rafter skews to the left. Its simple design makes installation intuitive and quick, resulting in lower labor costs. Featuring a versatile, hinged seat, the LSSJ26LZ is easily field-adjustable to typical rafter slopes, with a max slope of 12:12. It ships pre-bent with a 45° skew, making it ready to place for the most typical rafter conditions,...