Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson Strong-Tie SUL26Z Skewed Left 2 x 6/8 joist hangers with ZMax® coating are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will...
The Simpson Strong-Tie SUL26Z Skewed Left 2 x 6/8 joist hangers with ZMax® coating are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 6/8 joist end may be square or beveled cut. ZMax coating provides additional corrosion protection when required. Material: 16 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-9/16" (Wide) x 5" (Height) x 1-1/8" (Outside Flange) x...
Simpson Strong Tie U26 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material:...
Simpson Strong Tie U26 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 4-3/4" (Height) x 2" (Seat Depth) Fastener Options: (6) .162" x 3-1/2" 16d Nails (Header) (4) .148" x 1-1/2" 10d Nails (Joist) U26 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...
The Simpson Strong-Tie BA1.81/9.5 Top Flange Hanger is designed for 1-3/4" x 9-1/2" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn...
The Simpson Strong-Tie BA1.81/9.5 Top Flange Hanger is designed for 1-3/4" x 9-1/2" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn lumber and higher loads with engineered wood products. All BA hangers feature minimum nailing with positive-angle nailing (PAN) to target moderate load conditions and maximum nailing to support higher loads. Please Note: BA Hangers may be modified for slopes and/or skews up to 45°. The top...
The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...
The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT5ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 12 Glulam Beam - 5-1/8" x 10-1/2" Material: 12 Gauge Finish:...
Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH46-8/3 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance...
Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH46-8/3 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 2-7/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-8/3 Information and Installation Instructions. Gray Paint Coating Information...
Simpson Strong Tie HGUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge...
Simpson Strong Tie HGUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 7-1/8" (Height) x 5" (Seat Depth) Fastener Options: (36) 16d Nails (Header) (12) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS28 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...
Simpson Strong-Tie HTU210-2 Double 2 x 10 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU210-2 hanger very versatile...
Simpson Strong-Tie HTU210-2 Double 2 x 10 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU210-2 hanger very versatile for various trusses. Additionally you can have the HTU210-2 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is...
The Simpson Strong-Tie HU28TF is a hybrid 2 x 8 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that...
The Simpson Strong-Tie HU28TF is a hybrid 2 x 8 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 7-1/8" (Height) x 2-1/4" (Seat Depth) x 2-7/16" (Top Flange) Fasteners: (10)...
Simpson Strong Tie HUC26-2 Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HUC26-2 Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC26-2 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work. Material:...
Simpson Strong Tie HUCQ210-2SS-SDS Stainless Steel 3-1/4" Wide Double 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-2SS-SDS hangers...
Simpson Strong Tie HUCQ210-2SS-SDS Stainless Steel 3-1/4" Wide Double 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-2SS-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Type 316L Stainless Steel Dimensions: 3-1/4" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (12) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4"...
Simpson Strong Tie HUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...
Simpson Strong Tie HUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS28 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 7" (Height) x 3" (Seat Depth) Fastener...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS1.81/11.88 sets a new standard for engineered wood top flange hangers. The ITS1.81/11.88 installs 1-3/4" x 11-7/8"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS1.81/11.88 sets a new standard for engineered wood top flange hangers. The ITS1.81/11.88 installs 1-3/4" x 11-7/8" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1...
Simpson Strong-Tie IUS1.81/16 is used to install 1-3/4" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...
Simpson Strong-Tie IUS1.81/16 is used to install 1-3/4" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-7/8" (Wide) x 16" (Height) x 2" (Seat Depth) Fastener Options : (14) .148 x 3" Nails (Face-Min) (16) .148 x 3" Nails (Face-Max)...
The Simpson Strong-Tie LSSJ210RZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 10 jack rafters to hip/valley members when the rafter skews to the right. Its simple design...
The Simpson Strong-Tie LSSJ210RZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 10 jack rafters to hip/valley members when the rafter skews to the right. Its simple design makes installation intuitive and quick, resulting in lower labor costs. Featuring a versatile, hinged seat, the LSSJ210RZ is easily field-adjustable to typical rafter slopes, with a max slope of 12:12. It ships pre-bent with a 45° skew, making it ready to place for the most typical rafter...
The Simpson Strong-Tie LSSR2.1Z Slopeable and Skewable Rafter Hanger allows you to install either a 2" or 2-1/16" wide rafter with either a plumb cut or miter cut that has been tacked in place. This...
The Simpson Strong-Tie LSSR2.1Z Slopeable and Skewable Rafter Hanger allows you to install either a 2" or 2-1/16" wide rafter with either a plumb cut or miter cut that has been tacked in place. This versatile hanger is field adjustable for skewing up to 45° either left or right and features an innovative hinged swivel seat to adjust for up to a 45° slope. Material: 16 gauge Finish: ZMax® G-185 Coating Dimensions: 4-1/8" (Flange Width) x 8-15/16" (Height) x 2-1/8" (Joist Width)...
Simpson Strong-Tie LU26R-18 rough 2 x 6 Joist Hangers are an economical and time saving solution to securely installing rough 2 x 6 joists to a wood ledger or beam. You can install LU26R-18 hangers...
Simpson Strong-Tie LU26R-18 rough 2 x 6 Joist Hangers are an economical and time saving solution to securely installing rough 2 x 6 joists to a wood ledger or beam. You can install LU26R-18 hangers with 10d ,16d nails or #9 Strong-Drive® screws depending on the load value you are trying to achieve. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2" (Wide) x 4-9/16" (Height) x 1-1/2" (Seat Depth) Fastener Options: (6) .162 x 3-1/2" 16d Nails (Header) (4) .148 x 1-1/2" 10d...