Login/Register
Shopping Cart
OR
Simpson Strong-Tie ECCLLQ666SDS End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x...
Simpson Strong-Tie ECCLLQ666SDS End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x 2-1/2" wood screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Included Fasteners: 1/4" x 2-1/2" SDS Screws (Included) ECCLLQ666 Information and Installation Instructions....
Simpson Strong-Tie ECCQ66-SDS2.5HDG Hot Dipped Galvanized End Column Caps provide a high capacity connection between a 6x beam and a 6x post. ECCQ66-SDS2.5HDG End Column Caps should be used when the...
Simpson Strong-Tie ECCQ66-SDS2.5HDG Hot Dipped Galvanized End Column Caps provide a high capacity connection between a 6x beam and a 6x post. ECCQ66-SDS2.5HDG End Column Caps should be used when the beam ends at the post. Each ECCQ66-SDS2.5HDG End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Please Note: This column cap...
The Simpson Strong-Tie SUL214 Skewed Left 2 x 14 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists...
The Simpson Strong-Tie SUL214 Skewed Left 2 x 14 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 14 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 10" (Height) x 1-1/8" (Outside Flange) x 1-5/16" (Inside Flange) Fastener Options : (12) .162 x 3-1/2" 16d Nails (Face) (12) .148 x 1-1/2"...
The Simpson Strong-Tie PAB6-36 3/4" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB6-36 3/4" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
The Simpson Strong-Tie MTS30 1-1/4" Wide x 30" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or...
The Simpson Strong-Tie MTS30 1-1/4" Wide x 30" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS30 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 30" (Length)...
Simpson Strong-Tie H10ASS with Type 316L Corrosion Protection Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10ASS can also be field-bent to connect to shear blocking...
Simpson Strong-Tie H10ASS with Type 316L Corrosion Protection Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10ASS can also be field-bent to connect to shear blocking as well. The H10AZ uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Type 316L Stainless Steel Fastener Options: (18) 10d .148" x 1-1/2" H10ASS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L stainless steel is a nickel-chromium...
Simpson Strong Tie U410R Rough 4 x 10/12 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U410R Rough 4 x 10/12 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 4-1/16" (Wide) x 8-1/8" (Height) x 2" (Seat Depth) Fastener Options: (14) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 3" 10d Nails (Joist) U410R Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
Simpson Strong Tie HU210-4 Quad 2 x 10 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HU210-4 Quad 2 x 10 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU210-4 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 6-1/8" (Wide) x 8-3/8" (Height) x 2-1/2" (Seat Depth) Fastener...
The Simpson MIU4.12/14 hanger is designed to hang 4" x 14" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.12/14 features positive-angle...
The Simpson MIU4.12/14 hanger is designed to hang 4" x 14" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.12/14 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
The Simpson Strong-Tie THDB62400H4SS Type 304 Stainless Steel 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THDB62400H4SS Type 304 Stainless Steel 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie THDB62400H6SS Type 316 Stainless Steel 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THDB62400H6SS Type 316 Stainless Steel 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
Simpson Strong-Tie ECCLLQ666SDSHDG Hot Dipped Galvanized End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson...
Simpson Strong-Tie ECCLLQ666SDSHDG Hot Dipped Galvanized End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x 2-1/2" wood screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Included Fasteners: 1/4" x 2-1/2" SDS Screws (Included) ECCLLQ666SDSHDG Information...
Simpson Strong Tie HUC210-4 Quad 2 x 10 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HUC210-4 Quad 2 x 10 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC210-4 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work. Material:...
Simpson Strong Tie U414 4 x 14/16 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material:...
Simpson Strong Tie U414 4 x 14/16 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 10" (Height) x 2" (Seat Depth) Fastener Options: (16) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 3" 10d Nails (Joist) U414 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...
The Simpson Strong-Tie 3-1/2" x 16" MIT416 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...
The Simpson Strong-Tie 3-1/2" x 16" MIT416 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90 Galvanized...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.56/14 sets a new standard for engineered wood top flange hangers. The ITS2.56/14 installs 2-1/2" or 2-9/16" x 14"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.56/14 sets a new standard for engineered wood top flange hangers. The ITS2.56/14 installs 2-1/2" or 2-9/16" x 14" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from...
The Simpson Strong-Tie HU414TF is a hybrid 4 x 14 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing...
The Simpson Strong-Tie HU414TF is a hybrid 4 x 14 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 13" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (18) .162...
The Simpson Strong-Tie MTS30C 16ga. x 30" Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a...
The Simpson Strong-Tie MTS30C 16ga. x 30" Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS30C has a small bend section at the middle of the strap to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4"...
The Simpson Strong-Tie SSTB34HDG Hot Dipped Galvanized (7/8" Diameter by 34-7/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...
The Simpson Strong-Tie SSTB34HDG Hot Dipped Galvanized (7/8" Diameter by 34-7/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 8" Bolt Diameter: 7/8" Overall Length: 34-7/8" Minimum Embedment: 28-7/8" Finish: Hot...
Simpson Strong Tie LUS210-2SS Type 316L Stainless Steel 2 x 10/12 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for...
Simpson Strong Tie LUS210-2SS Type 316L Stainless Steel 2 x 10/12 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS210-2SS Double 2 x 10/12 Hangers are also approved for installation with SD10 Structural Screws. Material: 18 gauge Finish: Type 316L Stainless Steel Galvanized...
Simpson Strong-Tie H10AR Hurricane Tie for connection a double top plate to a 2x rough sawn rafter or truss. The H10AR can also be field-bent to connect to shear blocking as well. The H10AR uses...
Simpson Strong-Tie H10AR Hurricane Tie for connection a double top plate to a 2x rough sawn rafter or truss. The H10AR can also be field-bent to connect to shear blocking as well. The H10AR uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10AR Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of...
The Simpson Strong-Tie SUR214 Skewed Right 2 x 14 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate...
The Simpson Strong-Tie SUR214 Skewed Right 2 x 14 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 14 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 10" (Height) x 1-1/8" (Outside Flange) x 1-5/16" (Inside Flange) Fastener Options : (12) .162 x 3-1/2" 16d Nails (Face) (12) .148 x...
Simpson Strong-Tie CCQ66-SDS2.5HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 6x beam and a 6x post. CCQ66-SDS2.5HDG Column Caps should be used when the beam...
Simpson Strong-Tie CCQ66-SDS2.5HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 6x beam and a 6x post. CCQ66-SDS2.5HDG Column Caps should be used when the beam extends through the post. Each CCQ66-SDS2.5HDG Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Please Note: This column cap may be...
Simpson Strong Tie HGUS7.25/10 7-1/4" Wide Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material:...
Simpson Strong Tie HGUS7.25/10 7-1/4" Wide Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 7-1/4" (Wide) x 8-5/8" (Height) x 4" (Seat Depth) Fastener Options: (46) 16d Nails (Header) (16) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS7.25/10 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...