Login/Register
Shopping Cart
OR
Simpson Strong-Tie CB86 column bases are used to provide a connection of a 8 x 6 (7-1/2" x 5-1/2") post to concrete. The CB86 base is installed during the pouring of the concrete. Bolts run through...
Simpson Strong-Tie CB86 column bases are used to provide a connection of a 8 x 6 (7-1/2" x 5-1/2") post to concrete. The CB86 base is installed during the pouring of the concrete. Bolts run through the 8x side. Strap Material: 3 Ga. x 3" Wide Painted Simpson Gray Steel Base Material: 3 Ga Painted Simpson Gray (7-1/2" x 5-1/2") Fasteners: (2) 3/4" Machine Bolts CB86 Information and Installation Instructions Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...
Simpson Strong-Tie HDU14-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (36) 2-1/2" Simpson...
Simpson Strong-Tie HDU14-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (36) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 7 Gauge Steel Finish: Standard G90 Galvanized Anchor Bolt Diameter: 1" Pre-deflected...
Simpson Strong-Tie CCQ5-8SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 8x post. CCQ5-8SDS2.5 Column Caps should be used when the beam extends through the...
Simpson Strong-Tie CCQ5-8SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 8x post. CCQ5-8SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ5-8SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...
Simpson Strong-Tie CC76 Column Caps provide a high capacity connection between a 6-3/4" GluLam beam and a 6x post. CC76 Column Caps should be used when the 6-3/4" beam extends through the 6x post....
Simpson Strong-Tie CC76 Column Caps provide a high capacity connection between a 6-3/4" GluLam beam and a 6x post. CC76 Column Caps should be used when the 6-3/4" beam extends through the 6x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 6-7/8" (Beam) x 5-1/2" (Post) x 13"...
Simpson Strong-Tie MSTA36SS Type 316L Stainless Steel 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be...
Simpson Strong-Tie MSTA36SS Type 316L Stainless Steel 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-1/4" (Wide) x 36" (Length) Fasteners: (26) 10d...
Simpson Strong Tie LUS28-2SS Type 316L Stainless steel 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for...
Simpson Strong Tie LUS28-2SS Type 316L Stainless steel 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS28-2SS Double 2 x 8 Hangers are also approved for installation with SD10 Structural Screws. Material: 18 gauge Finish: Type 316L Stainless Steel Dimensions: 3-1/8" (Wide) x...
Simpson Strong Tie LUS28-3 2 x 8 Triple Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the...
Simpson Strong Tie LUS28-3 2 x 8 Triple Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS28-3 Triple 2 x 8 Hangers are also approved for installation with SD10 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 4-5/8" (Wide) x 6-1/4" (Height) x 2" (Seat Depth)...
Simpson Strong-Tie CS18-R 18-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS18-R are approved for use with SD Screws as a nail...
Simpson Strong-Tie CS18-R 18-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS18-R are approved for use with SD Screws as a nail substitution. 25' packs are an economical choice when you do not require large amounts. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 25' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS18-R Information and...
Simpson Strong-Tie ECCLL666 End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Please Note: This column cap may be available...
Simpson Strong-Tie ECCLL666 End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Please Note: This column cap may be available in Hot Dipped Galvanized as a special order. Additionally, multiple configurations can be manufactured up to 8x sizes. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2"...
Simpson Strong-Tie ECC78 End Column Caps provide a high capacity connection between a 6-3/4" Glulam beam and a 8x post. ECC78 End Column Caps should be used when the 6-3/4" beam ends at the 8x post....
Simpson Strong-Tie ECC78 End Column Caps provide a high capacity connection between a 6-3/4" Glulam beam and a 8x post. ECC78 End Column Caps should be used when the 6-3/4" beam ends at the 8x post. Please Note: This column cap is also available in powder coat or Hot Dipped Galvanized as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 6-7/8" (Beam) x 7-1/2" (Post) x 10-1/2" (Length) Fasteners:...
Simpson Strong-Tie HDU14-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come...
Simpson Strong-Tie HDU14-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (36) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 7 Gauge Steel Finish: Hot Dipped Galvanized Anchor Bolt...
Simpson Strong-Tie CB88 column bases are used to provide a connection of a 8 x 8 (7-1/2" x 7-1/2") post to concrete. The CB88 base is installed during the pouring of the concrete. Strap Material: 3...
Simpson Strong-Tie CB88 column bases are used to provide a connection of a 8 x 8 (7-1/2" x 7-1/2") post to concrete. The CB88 base is installed during the pouring of the concrete. Strap Material: 3 Ga. x 3" Wide Painted Simpson Gray Steel Base Material: 3 Ga Painted Simpson Gray (7-1/2" x 7-1/2") Fasteners: (2) 3/4" Machine Bolts CB88 Information and Installation Instructions Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint intended to only protect the...
The THD50500H 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...
The THD50500H 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...
Simpson Strong-Tie HL55PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55PC to connect lumber to concrete...
Simpson Strong-Tie HL55PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55PC to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Standard G90 Zinc Coating with a Black Powder Coat provides a low level of corrosion resistance. Material: 7 gauge Finish: Standard G90 Zinc Coating with a Black Powder Coat Dimensions: 5-3/4" (W1) x 5-3/4" (W2) x 5" (L) Bolt Holes: (8) 1/2" HL55PC Heavy...
Simpson Strong-Tie H7Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to both the top plate and rafter. The H7Z Tie requires (14) 8d...
Simpson Strong-Tie H7Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to both the top plate and rafter. The H7Z Tie requires (14) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (14) 8d x 1-1/2" Nails H7Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating)...
The Simpson Strong-Tie THD50600H6SS Type 316 Stainless Steel 1/2" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD50600H6SS Type 316 Stainless Steel 1/2" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie TNT18334TF Titen Turbo™ 3/16" x 3-3/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...
The Simpson Strong-Tie TNT18334TF Titen Turbo™ 3/16" x 3-3/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...
The Simpson Strong-Tie PAB5-36-HDG 5/8" x 36" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB5-36-HDG 5/8" x 36" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
The Simpson Strong-Tie 2-1/2" or 2-9/16" x 16" MIT316 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not...
The Simpson Strong-Tie 2-1/2" or 2-9/16" x 16" MIT316 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...
Simpson Strong-Tie Mission Outdoor Accents® APB1010 post bases secure a 10 x 10 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other...
Simpson Strong-Tie Mission Outdoor Accents® APB1010 post bases secure a 10 x 10 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported structures. These post bases feature decorative accents and provide Zmax® galvanization for extra corrosion resistance. Base includes black powder coating for a decorative look. APB1010 bases include a 1" standoff from the concrete to help avoid post-end rot caused by moisture. Designed to...
Simpson Strong Tie HGUS5.50/8 5-1/2" Wide Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material:...
Simpson Strong Tie HGUS5.50/8 5-1/2" Wide Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/2" (Wide) x 6-15/16" (Height) x 4" (Seat Depth) Fastener Options: (36) 16d Nails (Header) (12) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS5.50/8 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
Simpson Strong-Tie IUS2.37/16 is used to install 2-5/16" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...
Simpson Strong-Tie IUS2.37/16 is used to install 2-5/16" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-7/16" (Wide) x 16" (Height) x 2" (Seat Depth) Fastener Options : (14) .148 x 3" Nails (Face-Min) (16) .148 x 3" Nails...
The Simpson Strong-Drive® SDS25800 1/4" x 8" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25800 screw...
The Simpson Strong-Drive® SDS25800 1/4" x 8" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25800 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 8" Thread Length: 3-1/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive Type:...
Simpson Strong Tie HUCQ5.25/11-SDS Heavy Duty 5-1/8" Glulam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to use at...
Simpson Strong Tie HUCQ5.25/11-SDS Heavy Duty 5-1/8" Glulam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/4" (Wide) x 11" (Height) x 3" (Seat Depth) Included Fasteners: (14) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2" Screws (Joist) HUCQ5.25/11-SDS...