Login/Register
Shopping Cart
OR
Simpson Strong Tie HGUS5.25/12 5-1/8" Wide Glulam Hangers features double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12...
Simpson Strong Tie HGUS5.25/12 5-1/8" Wide Glulam Hangers features double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/4" (Wide) x 10-9/16" (Height) x 4" (Seat Depth) Fastener Options: (56) 16d Nails (Header) (20) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS5.25/12 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
Simpson Strong Tie U36 3 x 6/8 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16...
Simpson Strong Tie U36 3 x 6/8 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 5-3/8" (Height) x 2" (Seat Depth) Fastener Options: (8) .162 x 3-1/2" 16d Nails (Header) (4) .148 x 3" 10d Nails (Joist) U36 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...
The Simpson Strong-Tie THD50500H6SS Type 316 Stainless Steel 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD50500H6SS Type 316 Stainless Steel 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie HUC46TF is a hybrid 4 x 6 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two...
The Simpson Strong-Tie HUC46TF is a hybrid 4 x 6 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two concealed flanges for end-of-wall or corner installation. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 5-3/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (10)...
The Simpson Strong-Tie MTS20Z ZMax® 1-1/4" Wide x 20" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the...
The Simpson Strong-Tie MTS20Z ZMax® 1-1/4" Wide x 20" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS20 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. ZMax® coating provides additional corrosion resistance when required....
Simpson Strong-Tie Avant Outdoor Accents® APVB88DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APVB88 or APVB88R post base. These plates provide a...
Simpson Strong-Tie Avant Outdoor Accents® APVB88DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APVB88 or APVB88R post base. These plates provide a finished look to an installed post base. These decorative side plates provide a black powder coat finish over ZMax® galvanization for extra corrosion resistance. Install these side plates with Outdoor Accents® SDWS22312DBB structural wood screws and STN22 hex-head washers (sold separately)...
The Simpson Strong-Tie MTS20SS 1-1/4" Wide x 20" Long Stainless Steel Medium Twist Strap provides a tension connection between two members. This twist strap resists moderate uplift loads at the...
The Simpson Strong-Tie MTS20SS 1-1/4" Wide x 20" Long Stainless Steel Medium Twist Strap provides a tension connection between two members. This twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS20 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-1/4" (Wide) x 20"...
The Simpson MIU3.56/9 hanger is designed to hang 3-1/2" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU3.56/9 features...
The Simpson MIU3.56/9 hanger is designed to hang 3-1/2" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU3.56/9 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
The Simpson Strong-Tie SPH4 Heavy U-Shaped Stud Plate Tie is designed as a stud-to-plate connection to resist roof uplift. This heavy U-shaped strap has a horizontal portion that bears against the...
The Simpson Strong-Tie SPH4 Heavy U-Shaped Stud Plate Tie is designed as a stud-to-plate connection to resist roof uplift. This heavy U-shaped strap has a horizontal portion that bears against the wood wall top plates or sill plates and two vertical legs that are nailed to the edges of a wood stud. This tie is a cost-effective option when properly installed before the placement of the wall. SPH4R can be special ordered when the strap needs to be connected to a 1/2" shear wall also. Load rated...
The Simpson Strong-Tie® RTU2 Rigid Tie® Connector is designed for connecting intersecting members in wood construction applications. Manufactured to high-quality standards to ensure solid...
The Simpson Strong-Tie® RTU2 Rigid Tie® Connector is designed for connecting intersecting members in wood construction applications. Manufactured to high-quality standards to ensure solid performance, this U-shaped rigid tie features a G90 galvanized finish for added corrosion resistance. The versatile RTU2 is ideal for a variety of projects including fences, railings and utility furniture or any application where a 2x member crosses another. Fastens with Simpson Strong-Tie®...
Simpson Strong Tie U310 3 x 10/12 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material:...
Simpson Strong Tie U310 3 x 10/12 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 8-7/8" (Height) x 2" (Seat Depth) Fastener Options: (14) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 1-1/2" 10d Nails (Joist) U310 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
Simpson Strong Tie HUCQ5.25/9-SDS Heavy Duty 5-1/8" Glulam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to use at...
Simpson Strong Tie HUCQ5.25/9-SDS Heavy Duty 5-1/8" Glulam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/4" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (12) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2" Screws (Joist) HUCQ5.25/9 Information...
Simpson Strong Tie HUS412 4 x 12/14 Double Shear Beam Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also...
Simpson Strong Tie HUS412 4 x 12/14 Double Shear Beam Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 10-1/2" (Height) x 2" (Seat Depth) Fastener Options: (10) 16d Nails or SD10212 Screws (Header) (10) 16d Nails...
The Simpson Strong-Tie SUR210SS Type 316L Stainless Steel Skewed Right 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers...
The Simpson Strong-Tie SUR210SS Type 316L Stainless Steel Skewed Right 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. Stainless Steel provides additional corrosion protection when required. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.37/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.37/11.88 installs 2-5/16" x 11-7/8"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.37/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.37/11.88 installs 2-5/16" x 11-7/8" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.37/14 is used to install 2-5/16" x 14" I-Joist when a top flange hanger in not required. Installation is fast and easy...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.37/14 is used to install 2-5/16" x 14" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-7/16" (Wide) x 14" (Height) x 2" (Seat Depth) Fastener Options : (10)...
The Simpson Strong-Tie PAB5-36 5/8" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB5-36 5/8" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
The Simpson Strong-Tie TNT18334H Titen Turbo™ 3/16" x 3-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of...
The Simpson Strong-Tie TNT18334H Titen Turbo™ 3/16" x 3-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping and...
The Simpson Strong-Tie THD50600H4SS Type 304 Stainless Steel 1/2" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD50600H4SS Type 304 Stainless Steel 1/2" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson T15N250SFB 2-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The...
The Simpson T15N250SFB 2-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1...
The Simpson T15N250SFN 2-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The...
The Simpson T15N250SFN 2-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1...
Simpson Strong Drive® SSA16DB 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required...
Simpson Strong Drive® SSA16DB 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 1000 nails in the 25 lb. bucket. The nails are type 316 stainless steel providing high/severe corrosion protection. SSA16DB Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel...
Simpson Strong-Tie HL55HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55HDG to connect lumber...
Simpson Strong-Tie HL55HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55HDG to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Hot dipped galvanizing provide corrosion resistance from the elements or corrosive lumber. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 5-3/4" (W1) x 5-3/4" (W2) x 5" (L) Bolt Holes: (8) 1/2" HL55HDG Heavy Angle Information and...
The THD50400HMG Mechanical Galvanized 1/2" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD...
The THD50400HMG Mechanical Galvanized 1/2" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced...