Simpson Strong-Tie

Simpson Strong-Tie ECCQ5-6SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. ECCQ5-6SDS2.5 End Column Caps should be used when the beam ends at the...

Simpson Strong-Tie ECCQ5-6SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. ECCQ5-6SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ5-6SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call...

Simpson Strong-Tie CS16SS-R Stainless Steel 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16SS-R are approved for use with...

Simpson Strong-Tie CS16SS-R Stainless Steel 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16SS-R are approved for use with SD Screws as a nail substitution. 25' packs are an economical choice when you do not require large amounts. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-1/4" (Wide) x 25' (Length) Fasteners: 8d or 10d depending on end length and material (See link below for more information)...

Simpson Strong-Tie MSTA30 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x...

Simpson Strong-Tie MSTA30 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 30" (Length) Fasteners: (22) 10d Nails (22) SD9 x 1-1/2" Screws...

Simpson Strong-Tie ECCLRQ444HDG Hot Dipped Galvanized End Corner Column Caps provide a right connection between (2) 4x beams and (1) 4 x 4 posts when both beams end at the post. Install Simpson...

Simpson Strong-Tie ECCLRQ444HDG Hot Dipped Galvanized End Corner Column Caps provide a right connection between (2) 4x beams and (1) 4 x 4 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x 2-1/2" wood screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 3-1/2" (Beams) x 3-1/2" (Posts) Included Fasteners: 1/4" x 2-1/2" SDS Screws (Included) ECCLLQ444HDG Information and...

Simpson Strong-Tie ECCO9 End Column Caps with no straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The ECCO9 End Column Caps comes with no coating to allow you...

Simpson Strong-Tie ECCO9 End Column Caps with no straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The ECCO9 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 8-7/8" (Beam) x...

Simpson Strong Tie U214 2 x 14 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material:...

Simpson Strong Tie U214 2 x 14 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 10" (Height) x 2" (Seat Depth) Fastener Options: (12) .162" x 3-1/2" 16d Nails (Header) (8) .148" x 1-1/2" 10d Nails (Joist) U214 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...

Simpson Strong Tie LUS28Z ZMax® 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...

Simpson Strong Tie LUS28Z ZMax® 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS28Z 2 x 8 Hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-9/16" (Wide) x 6-5/8" (Height) x 1-3/4"...

Simpson Strong-Tie MSTA30Z ZMax® 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of...

Simpson Strong-Tie MSTA30Z ZMax® 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 16 gauge Finish: ZMax® G185 Galvanized Dimensions: 1-1/4" (Wide) x 30" (Length) Fasteners: (22) 10d Nails (22) SD9 x...

Simpson Strong-Tie LUC210Z ZMax® 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210Z also provides cleaner lines for exposed conditions...

Simpson Strong-Tie LUC210Z ZMax® 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210Z also provides cleaner lines for exposed conditions such as overhead decks. Material: 18 Gauge Finish: G-185 ZMax® Dimensions: 1-9/16" (Wide) x 7-3/4" (Height) x 1-3/4" (Seat Depth) Fastener Options: (10) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 1-1/2" 10d Nails (Joist) Strong Drive® SD9112 #9 x 1-1/2" Structural Screws may be substituted...

Simpson Strong-Tie LUC210SS Type 316L Stainless Steel 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210SS also provides cleaner lines for...

Simpson Strong-Tie LUC210SS Type 316L Stainless Steel 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210SS also provides cleaner lines for exposed conditions such as overhead decks. Material: 18 Gauge Finish:Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 7-3/4" (Height) x 1-3/4" (Seat Depth) Fastener Options: (10) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 1-1/2" 10d Nails (Joist) Strong Drive® SD9112 #9 x 1-1/2" Structural...

Simpson Strong Tie LUS28SS Type 316L Stainless Steel 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for...

Simpson Strong Tie LUS28SS Type 316L Stainless Steel 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS28SS 2 x 8 Hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 6-5/8"...

Simpson Strong-Tie CCO9 End Column Caps with no post straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The CCO9 Column Caps comes with no coating to allow you...

Simpson Strong-Tie CCO9 End Column Caps with no post straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The CCO9 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 8-7/8" (Beam) x 13"...

Simpson Strong-Tie CS16 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16 are approved for use with SD Screws as a nail...

Simpson Strong-Tie CS16 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16 are approved for use with SD Screws as a nail substitution. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 150' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS16 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...

Simpson Strong-Tie CCQ5-6SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. CCQ5-6SDS2.5 Column Caps should be used when the beam extends through the...

Simpson Strong-Tie CCQ5-6SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. CCQ5-6SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ5-6SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...

The Simpson Strong-Tie BCS2-2/4Z ZMax® allows for the connection of (2) 2x's to a 4x post. Double-shear nailing between beam and post gives added strength. The BC/BCS series offers dual-purpose...

The Simpson Strong-Tie BCS2-2/4Z ZMax® allows for the connection of (2) 2x's to a 4x post. Double-shear nailing between beam and post gives added strength. The BC/BCS series offers dual-purpose post cap/base for light cap or base connections. Install dome nails on beam; drive nails at an angle through the beam into the post below to achieve the table loads Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 3-9/16" (Post Width) x 3-1/8" (Joists Width) Fastener Options: (14) 10d...

The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...

The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 28-1/8" Minimum Embedment: 20-5/8" Finish: None Rolled threads for higher...

The Simpson Strong-Tie MAB15 mudsill anchor features design flexibility to anchor the mudsill to concrete block, poured walls or slab foundations. Because of its unique design, the MAB15 can...

The Simpson Strong-Tie MAB15 mudsill anchor features design flexibility to anchor the mudsill to concrete block, poured walls or slab foundations. Because of its unique design, the MAB15 can eliminate certain problems associated with misplaced anchor bolts. The MAB15 can be installed for 2x4,6,8,10 or 12 mudsills. Suitable for stem wall, concrete block or slab foundations One-piece design, so there are no nuts and washers to lose A easily installed alternative to standard anchor bolts 18 gauge...

Save by Purchasing a Quantity of 12 Boxes (48 Pieces)! Simpson Strong-Tie HDU11-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to...

Save by Purchasing a Quantity of 12 Boxes (48 Pieces)! Simpson Strong-Tie HDU11-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (30) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 10 Gauge Steel Finish: Standard...

Save by Purchasing a Quantity of 12 Boxes (120 Pieces)! The Simpson Strong-Tie HTT5-3/4 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This...

Save by Purchasing a Quantity of 12 Boxes (120 Pieces)! The Simpson Strong-Tie HTT5-3/4 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. Use this tie when you are using a 3/4" diameter anchor. HTT5-3/4 Tension Ties are designed to be used in both in vertical and horizontal...

Simpson Strong-Tie HL53HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL53HDG to connect lumber...

Simpson Strong-Tie HL53HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL53HDG to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Hot dipped galvanizing provide corrosion resistance from the elements or corrosive lumber. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 5-3/4" (W1) x 5-3/4" (W2) x 2-1/2" (L) Bolt Holes: (4) 1/2" HL53HDG Heavy Angle Information...

Simpson Strong Drive® SSA10D5 3" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as...

Simpson Strong Drive® SSA10D5 3" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 250 nails in the 5 lb. pack. The nails are type 316 stainless steel providing high/severe corrosion protection. SSNA10D Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel chromium...

The Simpson Strong-Tie Deck Drive™ DSVG212S #10 x 2-1/2" Gray Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...

The Simpson Strong-Tie Deck Drive™ DSVG212S #10 x 2-1/2" Gray Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVG212S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth...

The Simpson Strong-Tie TNT18314TF Titen Turbo™ 3/16" x 3-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...

The Simpson Strong-Tie TNT18314TF Titen Turbo™ 3/16" x 3-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...

The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...

The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...