Login/Register
Shopping Cart
OR
Simpson Strong-Tie ECCQ76SDS2.5 End Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 6x post. ECCQ76SDS2.5 End Column Caps should be used when the beam ends at the...
Simpson Strong-Tie ECCQ76SDS2.5 End Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 6x post. ECCQ76SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ76SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our...
Simpson Strong-Tie CCQ76SDS2.5 Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 6x post. CCQ76SDS2.5 Column Caps should be used when the beam extends through the...
Simpson Strong-Tie CCQ76SDS2.5 Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 6x post. CCQ76SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ76SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...
The THDB62400H 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...
The THDB62400H 5/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...
Simpson Strong-Tie ITS3.56/16 sets a new standard for engineered wood top flange hangers. The ITS3.56/16 installs 3-1/2" x 16" I-Joists faster and uses less nails than any other EWP top flange...
Simpson Strong-Tie ITS3.56/16 sets a new standard for engineered wood top flange hangers. The ITS3.56/16 installs 3-1/2" x 16" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the joist is...
The Simpson Strong-Tie PAB7-30-HDG 7/8" x 30" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB7-30-HDG 7/8" x 30" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
Simpson Strong-Tie H14 Hurricane Ties create a connection between either double top plates or double 2x header to a 2x rafter or truss. The bottom flange wrap the top plate but can be straightened...
Simpson Strong-Tie H14 Hurricane Ties create a connection between either double top plates or double 2x header to a 2x rafter or truss. The bottom flange wrap the top plate but can be straightened to face nail to a header. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (12) 8d x 1-1/2" Nails (Rafter/Truss) (13) or (15) 8d (Plates) H14 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
The Simpson Strong-Tie SUR1.81/11 Skewed 45° Right Hanger can be used when hanging a 1-3/4" x 11-1/4" or 11-7/8" engineered wood joists. The angles nail slots direct nails for proper...
The Simpson Strong-Tie SUR1.81/11 Skewed 45° Right Hanger can be used when hanging a 1-3/4" x 11-1/4" or 11-7/8" engineered wood joists. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 1-3/4" x 11-1/4" or 11-7/8" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-13/16" (Wide) x 11" (Height) x 1-5/8" (Outside Flange) x 2-5/16"...
Simpson Strong Tie LUS36 3 x 6/8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...
Simpson Strong Tie LUS36 3 x 6/8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS36 3 x 6/8 Hangers are approved for installation with 16D nails only. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 5-1/4" (Height) x 2" (Seat Depth) Fastener...
Simpson Strong Tie HU212-3 Triple 2 x 12 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HU212-3 Triple 2 x 12 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU212-3 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 4-11/16" (Wide) x 9-13/16" (Height) x 2-1/2" (Seat Depth)...
The Simpson MIU4.75/14 hanger is designed to hang 4-5/8" x 14" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.75/14 features positive-angle...
The Simpson MIU4.75/14 hanger is designed to hang 4-5/8" x 14" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.75/14 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
The Simpson Strong-Tie THDB62800H4SS Type 304 Stainless Steel 5/8" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THDB62800H4SS Type 304 Stainless Steel 5/8" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie THDB62800H6SS Type 316 Stainless Steel 5/8" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THDB62800H6SS Type 316 Stainless Steel 5/8" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson MIU4.75/16 hanger is designed to hang 4-5/8" x 16" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.75/16 features positive-angle...
The Simpson MIU4.75/16 hanger is designed to hang 4-5/8" x 16" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU4.75/16 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
Simpson Strong Tie LUS36Z ZMax® 3 x 6/8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...
Simpson Strong Tie LUS36Z ZMax® 3 x 6/8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS36Z 3 x 6/8 Hangers are approved for installation with 16D nails only. Material: 18 gauge Finish: ZMax® G-185 Galvanized Dimensions: 2-9/16" (Wide) x 5-1/4" (Height) x 2" (Seat Depth)...
The Simpson Strong-Tie SUR1.81/14 Skewed 45° Right Hanger can be used when hanging a 1-3/4" x 14" engineered wood joists. The angles nail slots direct nails for proper installation. These...
The Simpson Strong-Tie SUR1.81/14 Skewed 45° Right Hanger can be used when hanging a 1-3/4" x 14" engineered wood joists. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 1-3/4" x 14" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-13/16" (Wide) x 13-3/4" (Height) x 1-5/8" (Outside Flange) x 2-5/16" (Inside Flange) Base:...
Simpson Strong Tie HUC212-3 Triple 2 x 12 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HUC212-3 Triple 2 x 12 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC212-3 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work....
The Simpson Strong-Tie PAB7-36 7/8" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB7-36 7/8" x 36" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
The Simpson Strong-Tie HU610TF is a hybrid 6 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing...
The Simpson Strong-Tie HU610TF is a hybrid 6 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/2" (Wide) x 9-1/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (14)...
The THDB62500H 5/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...
The THDB62500H 5/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...
Simpson Strong-Tie ECCQ78SDS2.5 End Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 8x post. ECCQ78SDS2.5 End Column Caps should be used when the beam ends at the...
Simpson Strong-Tie ECCQ78SDS2.5 End Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 8x post. ECCQ78SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ78SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our...
Simpson Strong-Tie CCQ78SDS2.5 Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 8x post. CCQ78SDS2.5 Column Caps should be used when the beam extends through the...
Simpson Strong-Tie CCQ78SDS2.5 Column Caps provide a high capacity connection between a 6-3/4" Glulam Beam and a 8x post. CCQ78SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ78SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...
The Simpson Strong-Tie HUC610TF is a hybrid 6 x 10 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with...
The Simpson Strong-Tie HUC610TF is a hybrid 6 x 10 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two concealed flanges for end-of-wall or corner installation. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/2" (Wide) x 9-1/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (14)...
The Simpson Strong-Tie PAB7-36-HDG 7/8" x 36" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB7-36-HDG 7/8" x 36" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
The H16 Hurricane-Tie has a pre-sloped seat of 5/12 for double trusses. The pre-sloped seat of the H16 series ties provides for a tight fit and reduced deflection. The strap length provides for...
The H16 Hurricane-Tie has a pre-sloped seat of 5/12 for double trusses. The pre-sloped seat of the H16 series ties provides for a tight fit and reduced deflection. The strap length provides for various truss height up to a maximum of 13 1/2" (H16 series). Minimum heel height for H16 series is 4". Truss rafter pitch of 3/12 to 7/12 is acceptable. Shorter strap allows for less wrapping of straps when applicable. Material: 18 Gauge Width: 1-5/8" Height: 18-3/4" Finish: Standard G90 Zinc...