Post and Beam Caps

The Simpson Strong-Tie AC4 Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. Material: 18 Gauge Finish: Standard G90 Dimensions 3-9/16" (W) x 6-1/2" (L) Fastener Options: (16) 16d (Min) (28) 16d (Max) (28) SD10 x 1-1/2" (Max) AC4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a...

The Simpson BC4 Post Caps allow you to create a light duty connection between a 4 x 4 nominal post and 4x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 3-9/16" (W) x 3-9/16" (L) Fastener Options: (12) 16d or (12) SD10 x 1-1/2" BC4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...

The new CBT2Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether you’re designing for a custom indoor or outdoor living space, the tubular shape of the CBTZ allows an easy-to-install beam-to-post connection using common tools. The CBT2Z is designed to connect beams and posts of a variety of sizes. The CBT2Z accommodates a minimum 4x4 post and 4x6 beam using four steel dowel...

Simpson Strong-Tie ECC44 End Column Caps provide a high capacity connection between a 4x wide beam and a 4x post. ECC44 End Column Caps should be used when the 4x beam ends at the 4x post. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 3-5/8" (Post) x 5-1/2" (Length) Fasteners: (1) 5/8" Machine Bolt (Beam) , (2) 5/8" Machine Bolts (Post) ECC44 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a...

Simpson Strong-Tie ECCLL666 End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Fasteners: (6) 5/8" x 7" Machine Bolt (Beam & Post) ECCLL666 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint intended to only protect the product while it is being warehoused and...

Simpson Strong-Tie ECCO3 1/4 End Column Caps with no post straps provides a high capacity connection between a 3-1/8" wide beam and a steel post. The ECCO3 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-1/8" (Beam) x 7-1/2" (Length) Fasteners: (2) 5/8" Machine Bolt (Beam) ECCO3 1/4 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on...

Simpson Strong-Tie ECCQ44SDS2.5 End Column Caps provide a high capacity connection between a 4x beam and a 4x post. ECCQ44SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ44SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 3-5/8" (Post) x 8-1/2" (Length) Included Fasteners:...

Simpson Strong-Tie EPC44-16 (16 Gauge) End Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. EPC44-16 End Post Caps should be used when the beam ends at the post. 16-Gauge caps provide the same lateral loads as 12-Gauge caps but less uplift. Material:16 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 7-5/16" (Length) Fastener Options: (8) 16d (8) SD10 x 1-1/2" Screws EPC44-16 Information and Installation...

The Simpson Strong-Tie EPC4Z post cap is designed with the post and beam flanges in-line so that the EPC4Z end post cap can accommodate several 4x post sizes as well as double 2x4 studs. The EPC4Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 3-9/16" Dimensional Post Size: 4x4, 4x6, 4x8 or (2)...

The Simpson Strong-Tie AC4 Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. Material: 18 Gauge Finish: Standard G90 Galvanized Dimensions 3-9/16" (W) x 6-1/2" (L) Fastener Options: (16) 16d (Min) (28) 16d (Max) (28) SD10 x 1-1/2" (Max) AC4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating...

The Simpson BC4 ZMax® Post Caps allow you to create a light duty connection between a 4 x 4 nominal post and 4x nominal beam. ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 3-9/16" (W) x 3-9/16" (L) Fastener Options: (12) 16d or (12) SD10 x 1-1/2" BC4Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating...

The new CBT4Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether you’re designing for a custom indoor or outdoor living space, the tubular shape of the CBTZ allows an easy-to-install beam-to-post connection using common tools. The CBT4Z is designed to connect beams and posts of a variety of sizes. The CBT4Z accommodates a minimum 6x6 post and 6x8 beam using six steel dowel...

Simpson Strong-Tie CC44 Column Caps provide a high capacity connection between a 4x wide beam and a 4x post. CC44 Column Caps should be used when the 4x beam extends through the 4x post. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 3-5/8" (Post) x 7" (Length) Fasteners: (2) 5/8" Machine Bolts (Beam), (2) 5/8" Machine Bolts (Post) CC44 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based...

Simpson Strong-Tie CCO3 1/4 Column Caps with no post straps provides a high capacity connection between a 3-1/8" wide beam and a steel post. The CCO3 1/4 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-1/8" (Beam) x 11" (Length) Fasteners: (4) 5/8" Machine Bolt (Beam) CCO3 1/4 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on the...

Simpson Strong-Tie CCQ44SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ44SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 3-5/8" (Post) x 11" (Length) Included Fasteners: (30) 1/4" x...

Simpson Strong-Tie ECCLR666 End Corner Column Caps provide a right connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Fasteners: (6) 5/8" x 7" Machine Bolt (Beam and Post) ECCLR666 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint intended to only protect the product while it is being warehoused...

Simpson Strong-Tie PC44-16 (16 Gauge) Center Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. PC44-16 Center Post Caps should be used when the beam runs past the post. 16-Gauge caps provide the same lateral loads as 12-Gauge caps but less uplift. Material:16 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 11" (Length) Fastener Options: (10) 16d (10) SD10 x 1-1/2" Screws PC44-16 Information and Installation...

The Simpson Strong-Tie PC4Z Post Cap is designed with the post and beam flanges in-line so that the PC4Z center post cap can accommodate several 4x post sizes as well as double 2x4 studs. The PC4Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 3-9/16" Dimensional Post Size: 4x4, 4x6, 4x8 or (2)...

The Simpson ACE4 Split End Post Caps allow you to install the cap after the 4x post and 4x beam are set. The end cap should be used when the 4x beam ends at the 4x post. Material: 18 Gauge Finish: Standard G90 Galvanized Dimensions 4-1/2" (L) Fastener Options: (6) 16d (Min) (10) 16d (Max) (10) SD10 x 1-1/2" (Max) ACE4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of...

The Simpson Strong-Tie BC46 Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 3-9/16" (W) x 5-1/2" (L) Fastener Options: (18) 16d BC46 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion...

Simpson Strong-Tie ECC46 End Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. ECC46 End Column Caps should be used when the 4x beam ends at the 6x post. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 8-1/2" (Length) Fasteners: (2) 5/8" Machine Bolts (Beam) , (2) 5/8" Machine Bolts (Post) ECC46 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a...

Simpson Strong-Tie ECCLLQ666 End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x 2-1/2" wood screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Included Fasteners: (34) 1/4" x 2-1/2" SDS Screws ECCLLQ666 Information and Installation Instructions. Gray Paint...

Simpson Strong-Tie ECCO4 End Column Caps with no post straps provides a high capacity connection between a 4x wide beam and a steel post. The ECCO4 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-5/8" (Beam) x 5-1/2" (Length) Fasteners: (1) 5/8" Machine Bolt (Beam) ECCO4 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on the Simpson...

Simpson Strong-Tie ECCQ44-SDS2.5HDG Hot Dipped Galvanized End Column Caps provide a high capacity connection between a 4x beam and a 4x post. ECCQ44-SDS2.5HDG End Column Caps should be used when the beam ends at the post. Each ECCQ44-SDS2.5HDG End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Material: 7 gauge Finish: Hot...

Simpson Strong-Tie EPC44-16Z (16 Gauge) ZMax® End Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. EPC44-16Z End Post Caps should be used when the beam ends at the post. 16-Gauge caps provide the same lateral loads as 12-Gauge caps but less uplift. ZMax® coating offer additional corrosion protection when required. Material:16 gauge Finish: ZMax® G-185 Coating Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 7-5/16" (Length) Fastener Options:...

The Simpson Strong-Tie EPC6Z post cap is designed with the post and beam flanges in-line so that the EPC6Z end post cap can accommodate (3) 6x post sizes. The EPC6Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 5-1/2" Dimensional Post Size: 4x6, 6x6, or 6x8 Fasteners: (18) 10d Nails or SD9 x...

The Simpson ACE4 Split End Post Caps allow you to install the cap after the 4x post and 4x beam are set. The end cap should be used when the 4x beam ends at the 4x post. Material: 18 Gauge Finish: Standard G90 Galvanized Dimensions 4-1/2" (L) Fastener Options: (6) 16d (Min) (10) 16d (Max) (10) SD10 x 1-1/2" (Max) ACE4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of...

The Simpson BC46Z ZMax® Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. The ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 3-9/16" (W) x 5-1/2" (L) Fastener Options: (18) 16d BC46Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653...

Simpson Strong-Tie CC46 Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. CC46 Column Caps should be used when the 4x beam extends through the 6x post. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 11" (Length) Fasteners: (4) 5/8" Machine Bolts (Beam) , (2) 5/8" Machine Bolts (Post) CC46 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based...

Simpson Strong-Tie CCO4 End Column Caps with no post straps provides a high capacity connection between a 4x wide beam and a steel post. The CCO4 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-5/8" (Beam) x 7" (Length) Fasteners: (2) 5/8" Machine Bolt (Beam) CCO4 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on the Simpson Strong-Tie...

Simpson Strong-Tie CCQ44-SDS2.5HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44-SDS2.5HDG Column Caps should be used when the beam extends through the post. Each CCQ44-SDS2.5HDG Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Material: 7 gauge Finish: Hot Dipped...

Simpson Strong-Tie ECCLRQ666 End Corner Column Caps provide a right connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Install Simpson Strong-Tie SDS 1/4" x 2-1/2" wood screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Included Fasteners: (34) 1/4" x 2-1/2" SDS Screws ECCLLQ666 Information and Installation Instructions. Gray Paint...

Simpson Strong-Tie PC44-16Z (16 Gauge) ZMax® Center Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. PC44-16Z Post Caps should be used when the beam runs past the post. 16-Gauge caps provide the same lateral loads as 12-Gauge caps but less uplift. Material:16 gauge Finish: ZMax® G-185 Coating Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 11" (Length) Fastener Options: (10) 16d (10) SD10 x 1-1/2" Screws PC44-16Z Information and Installation...

The Simpson Strong-Tie PC6Z Center Post Cap is designed with the post and beam flanges in-line so that the PC6Z center post cap can accommodate (3) 6x post sizes. The PC6Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 5-1/2" Dimensional Post Size: 4x6, 6x6 or 6x8 Fasteners: (18) 10d Nails or SD9...

The Simpson BC6 Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 5-1/2" (W) x 5-1/2" (L) Fastener Options: (24) 16d BC6 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...

Simpson Strong-Tie ECC5 1/4-6 End Column Caps provide a high capacity connection between a 5-1/8" Glulam beam and a 6x post. ECC5 1/4-6 End Column Caps should be used when the 5-1/8" beam ends at the 6x post. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/4" (Beam) x 5-1/2" (Post) x 9-1/2" (Length) Fasteners: (2) 3/4" Machine Bolts (Beam) , (2) 3/4" Machine Bolts (Post) ECC5 1/4-6 Information and Installation Instructions. Gray Paint Coating Information Simpson...

Simpson Strong-Tie ECCO4/6 End Column Caps with no straps provides a high capacity connection between a 4x wide beam and a steel post. The ECCO4/6 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-5/8" (Beam) x 8-1/2" (Length) Fasteners: (2) 5/8" Machine Bolt (Beam) ECCO4/6 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on the Simpson...

Simpson Strong-Tie ECCQ46SDS2.5 End Column Caps provide a high capacity connection between a 4x beam and a 6x post. ECCQ46SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ46SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 8-1/2" (Length) Included Fasteners:...

Simpson Strong-Tie EPC44 (12 Gauge) End Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. EPC44 End Caps should be used when the beam ends at the post. 12-Gauge caps provide the same lateral loads as 16-Gauge caps but have a higher uplift value. Material:12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 7-5/16" (Length) Fastener Options: (8) 16d (8) SD10 x 1-1/2" Screws EPC44 Information and Installation...

The Simpson Strong-Tie EPC8Z post cap is designed with the post and beam flanges in-line so that the EPC8Z end post cap can accommodate (3) 8x post sizes. The EPC8Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 7-1/2" Dimensional Post Size: 4x8, 6x8, or 8x8 Fasteners: (18) 10d Nails or SD9 x...

The Simpson BC6Z ZMax® Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 5-1/2" (W) x 5-1/2" (L) Fastener Options: (24) 16d BC6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a...

Simpson Strong-Tie CC5 1/4-6 Column Caps provide a high capacity connection between a 5-1/8" GluLam beam and a 6x post. CC5 1/4-6 Column Caps should be used when the 5-1/8" beam extends through the 6x post. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/4" (Beam) x 5-1/2" (Post) x 13" (Length) Fasteners: (4) 3/4" Machine Bolts (Beam) , (2) 3/4" Machine Bolts (Post) CC5 1/4-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie...

Simpson Strong-Tie CCO4/6 End Column Caps with no post straps provides a high capacity connection between a 4x wide beam and a steel post. The CCO4/6 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Material: 7 gauge Finish: No Coating Dimensions: 3-5/8" (Beam) x 11" (Length) Fasteners: (4) 5/8" Machine Bolt (Beam) CCO4/6 Information and Installation Instructions. Additional Simpson Strong-Tie Information If there are any items on the Simpson...

Simpson Strong-Tie CCQ46SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 6x post. CCQ46SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ46SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 11" (Length) Included Fasteners: (30) 1/4" x...

Simpson Strong-Tie PC44 (12 Gauge) Center Post Caps provide a connection between a 4x wide beam and a 4x post at medium design loads. PC44 Center Post Caps should be used when the beam extends past the post. 12-Gauge caps provide the same lateral loads as 16-Gauge caps but have a higher uplift value. Material:12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Beam) x 3-9/16" (Post) x 11" (Length) Fastener Options: (10) 16d (10) SD10 x 1-1/2" Screws PC44 Information and Installation...

The Simpson Strong-Tie PC8Z Center Post Cap is designed with the post and beam flanges in-line so that the PC8Z center post cap can accommodate (3) 8x post sizes. The PC8Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Width: 7-1/2" Dimensional Post Size: 4x8, 6x8 or 8x8 Fasteners: (18) 10d Nails or SD9...

The Simpson AC4Z ZMax® Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. ZMax® protection provides additional corrosion resistance when applicable. Material: 18 Gauge Finish: ZMax® G-185 Galvanized Dimensions 3-9/16" (W) x 6-1/2" (L) Fastener Options: (16) 16d (Min) (28) 16d (Max) (28) SD10 x 1-1/2" (Max) AC4Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized...

The Simpson BC8 Post Caps allow you to create a light duty connection between a 8 x 8 nominal post and 8x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 7-1/2" (W) x 7-1/2" (L) Fastener Options: (24) 16d BC8 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...