Products 1-24 of 64
Show
Availability: Stock
GST International
Item #: GST507G -
GST International's Final Coat Floor Polish is the premier high solids acrylic polymer floor polish for gloss and durability. It represents the first major improvement in masonry floor care technology within the last 5 years. Its' 29% high solids formulation provides maximum scuff and heel mark resistant gloss for lower maintenance costs. Final Coat requires fewer coats than are needed with conventional lower solids products and stays glossy even after numerous scrubs. Also, it has the...
Availability: Stock
GST International
Item #: E-ARMOR10 -
The World’s Most Amazing Cementitious Repair and Overlay Product! GST Interntional Elephant Armor® DOT is a single component, cementitious, fiber reinforced, ultra-fast setting concrete repair and overlay mortar that can be placed with a textured roller, traditional placement tools or other types of high volume application equipment. This ultra-high performance mortar with its high early and superior bond strength (4000 psi in 4 hours) offers unlimited possibilities for repair work,...
Availability: Stock
CWC
Item #: STR12F -
CWC 135-072 #18 x 550' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend, lower stress point than braided seine twine. Ties easily and knots securely. Common to the marine, electrical and construction industries, this twine is also useful in home and garden applications. Resists abrasion, mildew and most chemicals Used for chalk line, fishing line and net repair #18 Size ...
Availability: Stock
Fab-Form
Item #: FASTFOOT18 -
FASTFOOT® FF50 Fabric Forms eliminated the use of heavy dimensional lumber and plywood when forming footing 18" wide by 10" deep or less. Because of the speed of preparation and tear down the FASTFOOT® system offers a great labor savings. Prevents Concrete Damage - Fastfoot® is a closed form. There is no concrete damage to screed boards and stakes. This means your 2x4s and stakes can be re-used indefinitely. Adapts to Uneven Ground, Rock - Special colored width lines allow...
Availability: Stock
Grip-Rite
Item #: TW4 -
The 4" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 4" Bar Ties Various Rebar Combinations: #2 Bar (1/4") to #3 Bar (3/8") ...
Spotlight!
Availability: Stock
Krylon Industrial
Item #: 03620 -
Krylon Industrial Fluorescent Caution Blue Quik-Mark™ Water-Based Inverted Marking Paint offers an advanced UV resistant formula. This formula allows you to mark your lines during harsh or adverse conditions, even in extreme sun. The Quik-Mark™ advanced UV resistant formulas will not fade to a different color! Accuracy, speed and ease of marking will keep your locators efficient and productive while lowering the overall costs of a ticket. Total marking paint performance eliminates...
Availability: Stock
OCM, Inc.
Item #: CHAIR2 -
OCM 2" or 2-1/4" PCC2.00-2.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 3-1/2" base diameter Fits up to #8 rebar Will not puncture...
Availability: Stock
OCM, Inc.
Item #: STSEC-6HH -
OCM, Inc #STSEC-6HH 6" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
OCM, Inc.
Item #: SC06-75 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 6" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
Simpson Strong-Tie
Item #: AM5/8 -
Simpson Strong Tie AnchorMate® 5/8" Anchor Bolt Holders are designed to hold 5/8" anchor bolts including SSTB Bolts in place before the concrete pour. With a unique grip placed properly there is no need for a hex nut during the pour. Additionally and Anchormate® protects the threads from splashed concrete. Built-in 2x4 and 2x6 stops eliminate measuring. Elevated bolt grippers allow easy trowel finishing. Color-coded for easy size identification. Lightweight, durable and easy to use....
Availability: Stock
Simpson Strong-Tie
Item #: WT6 -
The Simpson Strong-Tie WT-6 Wedge Form Ties are designed for low foundation wall applications with a 6" width. Their 5/8" wide formed "V" design for rigidity allows accurate form spacing and support. Material: 14 Gauge Galvanized Use two 3-1/2" long wedges for each tie. Not recommended for wall pours greater than 4' high. Wall thickness from 6". Refer to technical bulletin T-WT for recommended spacing. Please Note: Wedges are sold separately. Additional Simpson Strong-Tie Information If there...
Availability: Stock
CWC
Item #: STR1F -
CWC 135-127 #18 x 1,100' Fluorescent Pink Twisted Seine Twine (also referred to as chalk or mason line) has excellent resistance to rot, abrasion, water, oil, grease and most chemicals. Less bend, lower stress point than braided seine twine. Ties easily and knots securely. Common to the marine, electrical and construction industries, this twine is also useful in home and garden applications. Resists abrasion, mildew and most chemicals Used for chalk line, fishing line and net repair #18 Size ...
Availability: Stock
Grip-Rite
Item #: TW6 -
The 6" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 6" Bar Ties Various Rebar Combinations: #4 Bar (1/2") to #6 Bar (3/4") #5 Bar (5/8") to #5...
Availability: Stock
OCM, Inc.
Item #: STLEC-6HH -
OCM, Inc #STLEC-6HH 6" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties use...
Availability: Ships Direct
OCM, Inc.
Item #: SC0762-118 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 7-5/8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
OCM, Inc.
Item #: JAHN-A -
OCM ACLMP Jahn-A Bracket is fabricated from high strength steel with a cad plated eccentric and painted body. The 5/8" take-up of the eccentric compensates for minor lumber variations in thickness. This Jahn-A Bracket can be utilized to hold a single horizontal wale or a single vertical stud with any type of wall form; round, curved, battered, beam and/or columns. The Jahn-A Bracket can be installed before or after the wales have been positioned. The slots in the bracket allow it to slip over...
Availability: Stock
Simpson Strong-Tie
Item #: WT8 -
The Simpson Strong-Tie WT-8 Wedge Form Ties are designed for low foundation wall applications with a 8" width. Their 5/8" wide formed "V" design for rigidity allows accurate form spacing and support. Material: 14 Gauge Galvanized Use two 3-1/2" long wedges for each tie. Not recommended for wall pours greater than 4' high. Wall thickness from 8". Refer to technical bulletin T-WT for recommended spacing. Please Note: Wedges are sold separately. Additional Simpson Strong-Tie Information If there...
Availability: Stock
Fab-Form
Item #: FASTFOOT18-C -
FASTFOOT® 18" Sewn Corners are the perfect accessory to the 18" FASTFOOT® Footing on a roll. Using these sewn corners means no cutting and can easily be installed by one person. The FASTFOOT® Corners are 4' x 4' giving you approximately 6 lineal feet of forms when figuring in the over lap. Forms 90° corners Saves time and labor No required cutting
Availability: Stock
Grip-Rite
Item #: TW8 -
The 8" bar ties are black annealed 17 gauge wire with loops on each end. Using either a Spring Loaded Automatic Bar Tie Twister or a Wood Handled Bar Tie Twister rebar tying is a snap. Just pull the tie around the joint, attach the hook on your tying tool, twist or pull and you are done. Please Note: If you are not sure what size you need you can view the Bar Tie Chart to see which ties you will need. 8" Bar Ties Various Rebar Combinations: #4 Bar (1/2") to #10 Bar (1-1/4") #5 Bar (5/8") to #8...
Spotlight!
Availability: Out of Stock
Krylon Industrial
Item #: 03500 -
Krylon Industrial 03500 Clear QUIK-MARK™ Water-Based Inverted Marking Paint offers an advanced UV resistant formula. This formula allows you to mark your lines during harsh or adverse conditions, even in extreme sun. The Quik-Mark™ advanced UV resistant formulas will not fade to a different color! Accuracy, speed and ease of marking will keep your locators efficient and productive while lowering the overall costs of a ticket. Total marking paint performance eliminates costly...
Availability: Stock
OCM, Inc.
Item #: CHAIR3 -
OCM 3" or 3-1/4" PCC3.00-3.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 4-1/8" base diameter Fits up to #8 rebar Will not puncture...
Availability: Stock
OCM, Inc.
Item #: STSEC-8HH -
OCM, Inc #STSEC-8HH 8" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
OCM, Inc.
Item #: SC08-75 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 8" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
OCM, Inc.
Item #: STWEGP -
OCM STWEGP Snap-Tie Wedges (also known as hairpin wedges) can either be used in a double waler forming system or applies directly to the plywood when using stubby snap ties. The OCM STWEGP Snap-Tie Wedges is a high strength snap tie wedge with a safe working load of 3,325 lbs. It is designed to slip over the head of standard or heavy duty snap ties to provide ample bearing area for proper load distribution into the wales. The wedge can also be applies directly to the plywood when using stubby...