Simpson Strong-Tie

Simpson Strong-Tie ITS1.81/9.5 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/9.5 installs 1-3/4" x 9-1/2" I-Joists faster and uses less nails than any other EWP top...

Simpson Strong-Tie ITS1.81/9.5 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/9.5 installs 1-3/4" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the...

The Simpson CBSQ44-SDS2HDG Hot Dipped Galvanized (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1"...

The Simpson CBSQ44-SDS2HDG Hot Dipped Galvanized (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Hot Dipped Galvanized for additional corrosion resistance. Easier Installation Higher Loads Hot Dipped Galvanized Column Size: 4 x 4 Nominal (3-1/2" x 3-1/2") Base: 12 Ga. (3-9/16" x...

The Simpson Strong-Tie CJT4ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT4ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT4ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 10 Glulam Beam - 3-1/8" x 9" PSL - 3-1/2 x...

Simpson Strong Tie AnchorMate® 7/8" Anchor Bolt Holders are designed to hold 7/8" anchor bolts including SSTB Bolts in place before the concrete pour. With a unique grip placed properly there is...

Simpson Strong Tie AnchorMate® 7/8" Anchor Bolt Holders are designed to hold 7/8" anchor bolts including SSTB Bolts in place before the concrete pour. With a unique grip placed properly there is no need for a hex nut during the pour. Additionally and Anchormate® protects the threads from splashed concrete. Built-in 2x4 and 2x6 stops eliminate measuring. Elevated bolt grippers allow easy trowel finishing. Color-coded for easy size identification. Lightweight, durable and easy to use....

Simpson Strong-Tie CB44HDG Hot Dipped Galvanized column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the...

Simpson Strong-Tie CB44HDG Hot Dipped Galvanized column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 2" Wide Hot Dipped Galvanized Steel Base Material: 7 Ga Hot Dipped Galvanized (3-9/16" x 3-9/16") Fasteners: (2) 5/8" Machine Bolts CB44HDG Information and Installation Instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the...

Simpson Strong-Tie LSTA15 20 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x...

Simpson Strong-Tie LSTA15 20 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a LSTA strap that requires bending the strap can only be bent one time. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 15" (Length) Fasteners: (12) 10d Nails (12) SD9 x 1-1/2" Screws...

Simpson Strong-Tie CMST14 Coil Strap allows you to install 3" wide strapping at various lengths depending on your span requirements. CMST14 are approved for use with SD Screws as a nail...

Simpson Strong-Tie CMST14 Coil Strap allows you to install 3" wide strapping at various lengths depending on your span requirements. CMST14 are approved for use with SD Screws as a nail substitution. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3" (Wide) x 52-1/2' (Length) Fasteners: 10d or 16d depending on end length and material (See information link below) CMST14 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc...

Simpson Strong-Tie ST18 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications....

Simpson Strong-Tie ST18 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 17-3/4" (Length) Fastener Options: (14) 16d Nails (14) SD10 x 1-1/2" Screws ST18 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains...

The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to...

The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

The Simpson Strong-Tie DSC5L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are...

The Simpson Strong-Tie DSC5L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5L-SDS3 series drag strut connectors requires 40% less fasteners than the DSC4L connector but gets 12% higher loads. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS 1/4" x 3" DSC5L-SDS3...

The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-8 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie DTT2Z ZMax® Tension Tie is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the deck joists, rather than to...

The Simpson Strong-Tie DTT2Z ZMax® Tension Tie is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the deck joists, rather than to the rim joist alone, the connection is stronger than typical through-bolt installations and complies with IRC and IBC code requirements regarding handrail and guardrail post connections for decks. The DTT2Z also complies with the new IRC requirements for laterally tying the deck to the house....

With the Simpson Strong-Tie SDWC15600-KT 6" Structural Screws you will now have the flexibility to provide an approved connection even after the exterior shear wall has been installed. The labor...

With the Simpson Strong-Tie SDWC15600-KT 6" Structural Screws you will now have the flexibility to provide an approved connection even after the exterior shear wall has been installed. The labor savings installing the SDWC15600-KT 6" Structural Screws as opposed to installing traditional ties and straps will more than offset the costs of the fasteners. The 6-lobe drive using a T-30 bit reduces your chance of stripping out the screw, enabling a quick and secure installation. Fully threaded...

The Simpson Strong-Tie HDQ11-SDS2.5 holdown combines low deflection and high loads with ease of installation. (24) 2-1/2" SDS Simpson Strong-Tie® Strong-Drive® screws are included which...

The Simpson Strong-Tie HDQ11-SDS2.5 holdown combines low deflection and high loads with ease of installation. (24) 2-1/2" SDS Simpson Strong-Tie® Strong-Drive® screws are included which install easily, reduces fastener slip and provide a greater net section area of the post when compared to bolts. They may be installed either flush or raised off the mudsill without a reduction in load value. Material: 7 Gauge Steel Finish: Simpson Gray Paint Anchor Bolt Size: 1" Minimum Post Thickness:...

The Simpson Strong-Tie® Strong-Drive® SDWS22400DB .220" x 4" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects...

The Simpson Strong-Tie® Strong-Drive® SDWS22400DB .220" x 4" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects where a high-strength attachment is needed. The 0.220" diameter of the SDWS22400DB 4" wood screw requires less torque to install than comparable fasteners, making it easier to drive. The Double-Barrier Coating corrosion-resistant coating makes it suitable for many interior and exterior applications....

Simpson Strong-Tie HTU28 2 x 8 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU28 hanger very versatile for various...

Simpson Strong-Tie HTU28 2 x 8 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU28 hanger very versatile for various trusses. Additionally you can have the HTU28 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is 1/8" per ASTM...

The Simpson Strong-Tie® Strong-Drive® SDWH19400DB 4" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter...

The Simpson Strong-Tie® Strong-Drive® SDWH19400DB 4" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter fastener requires less torque to install than comparable fasteners, making it easier to drive; while the corrosion-resistant coating makes it suitable for many interior and exterior applications. The large hex washer head of the SDWH19400DB 4" screw creates an excellent bearing area for a secure...

Simpson Strong-Tie EPB44HDG allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus...

Simpson Strong-Tie EPB44HDG allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Hot Dip Galvanizing provides corrosion resistance for additional...

The Simpson PB44Z ZMax® Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. ZMax® Coated for...

The Simpson PB44Z ZMax® Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. ZMax® Coated for extra corrosion resistance Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Nails PB44Z information and installation instructions ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating) than the...

The Simpson Strong-Tie HD5B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This is required so that the wood...

The Simpson Strong-Tie HD5B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This is required so that the wood is not weakened from drilling too close to the end. However the anchor can still be installed raised above the sill plate if you desire. All the HDB style holdown anchors are designed to provide loads for intermediate-load-range shearwalls, braced wall panels and lateral applications. Base...

The Simpson Strong-Tie ABW46Z for 4x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete...

The Simpson Strong-Tie ABW46Z for 4x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW46Z allows...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD9212 #9 x 2-1/2"...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD9212 #9 x 2-1/2" structural connector screws are approved to replace nails in certain Simpson Strong-Tie Connectors. The advantages of using screws can be ease of installation in tight spots and less vibration when installing connectors during remodel projects. The shank of the SD9112 screws are designed to easily fit in...

The Simpson Strong-Tie EPC6Z post cap is designed with the post and beam flanges in-line so that the EPC6Z end post cap can accommodate (3) 6x post sizes. The EPC6Z now uses easier-to-install 10d...

The Simpson Strong-Tie EPC6Z post cap is designed with the post and beam flanges in-line so that the EPC6Z end post cap can accommodate (3) 6x post sizes. The EPC6Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Please Note: This cap may be special ordered in a rough dimensional size as a manufactured...

The S/HDU6 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU6 holdown...

The S/HDU6 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU6 holdown combines performance with ease of installation using #14 screws self-drilling tapping screws thus saving time and labor.. The pre-deflected geometry virtually eliminates material stretch, resulting in low deflection under load. Foundation Anchor Diameter: 5/8" Fasteners (Not Included): (12) #14 Screws...