Simpson Strong-Tie

The Simpson Strong-Tie LS50Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS...

The Simpson Strong-Tie LS50Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time. Flanges are 2-1/4" wide. LS50Z Angles can use 10d .148" x 1-1/2" or longer nails depending on the application. Material: 18 Gauge Finish: ZMax® Coating Length: 4-7/8" Flange Widths: 2-1/4" x 2-1/4" Fasteners: (8) 10d x 1-1/2" Nails LS50Z Information and...

Simpson Strong-Tie N10D5HDG-R 1-1/2" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 600 nails in the 5 lb....

Simpson Strong-Tie N10D5HDG-R 1-1/2" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 600 nails in the 5 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. N10D5HDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average...

The Simpson Strong-Tie SSTB16L (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...

The Simpson Strong-Tie SSTB16L (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 19-5/8" Minimum Embedment: 12-5/8" Finish: None Rolled threads for higher...

Simpson Strong-Tie PBS46 Standoff Post Bases are used to connect a 4 x 6 (3-1/2" x 5-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over...

Simpson Strong-Tie PBS46 Standoff Post Bases are used to connect a 4 x 6 (3-1/2" x 5-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over time. Available only in standard galvanizing. Finish: Standard G90 Galvanized Base Material: 12 Gauge Base Dimensions: 3-9/16" x 5-7/16" Strap Material: 14 Gauge Strap Height: 6-9/16" Fastener Options: (14) 16d (2) 1/2" Machine Bolts Additional PBS46 information and installation instructions...

The Simpson Strong-Drive® SDS25200 1/4" x 2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25200 screw...

The Simpson Strong-Drive® SDS25200 1/4" x 2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25200 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 2" Thread Length: 1-1/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive Type:...

Simpson Strong-Tie HRS416Z 12-Gauge 3-1/4" Wide Heavy Strap Ties are designed to splice 2 x 4 or larger lumber using the face. This splice strap uses SDS25112 structural screws to reach desired...

Simpson Strong-Tie HRS416Z 12-Gauge 3-1/4" Wide Heavy Strap Ties are designed to splice 2 x 4 or larger lumber using the face. This splice strap uses SDS25112 structural screws to reach desired load. Material: 12 gauge Finish: ZMax® G185 Galvanized Dimensions: 3-1/4" (Wide) x 16" (Length) Fastener Options: (16) 1/4" x 1-1/2" SDS Screws HRS416Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653...

Simpson Strong-Tie Avant Outdoor Accents® APVA4 angles tie together beams, rafters and more. The APVA4 angle makes structural connections between beams and posts much more visually appealing....

Simpson Strong-Tie Avant Outdoor Accents® APVA4 angles tie together beams, rafters and more. The APVA4 angle makes structural connections between beams and posts much more visually appealing. These angles make connections stronger and provide consistent, straight corners for a variety of outdoor projects. Using The Outdoor Accents® structural screws and STN22 Shear Tube nuts allows you to create an outdoor gazebo, patio cover etc. that is not only structurally sound but pleasing to the...

Simpson Strong-Tie EPB44-12 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus...

Simpson Strong-Tie EPB44-12 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and un-braced carports. Finish: Simpson Gray Paint Pipe Size: 1-1/16" OD x 8" Length Base...

Simpson Strong-Tie Avant Outdoor Accents® flat APVL6 "L" straps bring decorative appeal and lateral strength to any outdoor living space like patio covers, gazebos and more. The APVL6 "L"...

Simpson Strong-Tie Avant Outdoor Accents® flat APVL6 "L" straps bring decorative appeal and lateral strength to any outdoor living space like patio covers, gazebos and more. The APVL6 "L" provide reinforcement for a connection where two 6x or larger lumber pieces intersect at a 90-degree angle. These straps are easily installed with Outdoor Accents structural screws and hex-head washers. The Avant Collection features straight edges and chamfered corners for a clean, timeless design Install...

The Simpson Strong-Tie APVDJT1.75-4 Avant Outdoor Accents® Deck Joist Tie attaches 1-3/4" beams to the side of 4x or larger support posts. It installs quickly and easily with the Outdoor Accents...

The Simpson Strong-Tie APVDJT1.75-4 Avant Outdoor Accents® Deck Joist Tie attaches 1-3/4" beams to the side of 4x or larger support posts. It installs quickly and easily with the Outdoor Accents structural wood screw and hex-head washer for the look of a bolted connection. The Avant Collection features straight edges and chamfered corners for a clean, timeless design. Designed to meet stringent building codes for seismic or high-wind events Install with Outdoor Accents® structural wood...

Simpson Strong-Tie Avant Outdoor Accents® APVB44 post bases secure a 4 x 4 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported...

Simpson Strong-Tie Avant Outdoor Accents® APVB44 post bases secure a 4 x 4 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported structures. These post bases feature a clean, simple design and provide ZMAX® galvanization with black powder coat for extra corrosion resistance. APVB44 bases include a 1" standoff from the concrete to help avoid post-end rot caused by moisture. The Avant Collection features straight edges and...

The Simpson Strong-Tie VPA2.1 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/16" wide rafters to the top plate. It will adjust to accommodate...

The Simpson Strong-Tie VPA2.1 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2-1/16" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-1/8" Actual Joist Width:...

The Simpson Strong-Tie ML24Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood...

The Simpson Strong-Tie ML24Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood splitting and opposing hole patterns allow for back-to-back installation without fastener interference. Please Note: SDS screws are not included. Finish: ZMax® coating Material: 12 Gauge Fasteners (Not Included): (6) SDS25112 Screws Dimensions: 4" Length x 2" (Flange Widths) ML24Z Information and...

The Simpson Strong-Tie RBC roof boundary clip is designed to aid installation and transfer shear loads between the roof diaphragm and wall. The locator tabs make proper location of the clip easy....

The Simpson Strong-Tie RBC roof boundary clip is designed to aid installation and transfer shear loads between the roof diaphragm and wall. The locator tabs make proper location of the clip easy. The RBC can be used on wood or masonry walls and will handle roof pitches from 0/12 to 12/12. The RBC is available as a special order with prongs into one side (RBCP) for pre-attachment of the part to a block at the truss plant. Material: 20 Gauge Finish: Standard G90 Zinc Fasteners-to-blocking: (6)...

The Simpson Strong-Tie PAB4-24 1/2" x 24" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...

The Simpson Strong-Tie PAB4-24 1/2" x 24" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...

The Simpson Strong-Drive® SDWS16300Q 3" x .160" Framing screw is designed and load-rated for replacing 16d, 10d and 8d nails in multiple types of framing applications. The SDWS Framing screw is...

The Simpson Strong-Drive® SDWS16300Q 3" x .160" Framing screw is designed and load-rated for replacing 16d, 10d and 8d nails in multiple types of framing applications. The SDWS Framing screw is 0.160" in diameter and superior to nails in holding power and pull-out resistance. It is code listed under IAPMO UES ER-192 and meets 2012 and 2015 IRC® and IBC® code requirements for several common wood framing and engineered-wood applications. The screw has a SawTooth™ point that makes for...

Simpson Strong-Tie Outdoor Accents® APHH610R concealed flange heavy hangers connect rough sawn 6 x 10 or 6 x 12 beams to girders or ledgers. These concealed-flange hangers feature straight edges...

Simpson Strong-Tie Outdoor Accents® APHH610R concealed flange heavy hangers connect rough sawn 6 x 10 or 6 x 12 beams to girders or ledgers. These concealed-flange hangers feature straight edges and provide a cleaner-looking installation for joist connections. The APHH610R heavy hanger installs easily with the Outdoor Accents® SDWS22312DBB connector screws and STN22 hex-head washers. Use Strong-Drive SDS25300 Heavy-Duty Connector screws to connect to the header Install with Outdoor...

Simpson Strong-Tie Outdoor Accents® APLH26R concealed flange light hangers connect rough sawn 2 x 6 or 2 x 8 joists to beams. These concealed-flange hangers feature straight edges and provide a...

Simpson Strong-Tie Outdoor Accents® APLH26R concealed flange light hangers connect rough sawn 2 x 6 or 2 x 8 joists to beams. These concealed-flange hangers feature straight edges and provide a cleaner-looking installation for joist connections. The APLH26R hanger installs easily with the Outdoor Accents® connector screw. Install with Outdoor Accents® SD10112DBB structural screws for a decorative look and meet required load values. Designed for use with rough 2 x 6 and 2 x 8...

The THDB25312H 1/4" x 3-1/2" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal...

The THDB25312H 1/4" x 3-1/2" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The...

The Simpson Strong-Tie LSSJ28RZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 8 jack rafters to hip/valley members when the rafter skews to the right. Its simple design makes...

The Simpson Strong-Tie LSSJ28RZ Field-Adjustable Jack Hanger is the ideal hanger for connecting a 2 x 8 jack rafters to hip/valley members when the rafter skews to the right. Its simple design makes installation intuitive and quick, resulting in lower labor costs. Featuring a versatile, hinged seat, the LSSJ28RZ is easily field-adjustable to typical rafter slopes, with a max slope of 12:12. It ships pre-bent with a 45° skew, making it ready to place for the most typical rafter conditions,...

The Simpson Strong-Tie DTT2Z-SDS2.5 ZMax® Tension Tie with 2-1/2" Screws is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the...

The Simpson Strong-Tie DTT2Z-SDS2.5 ZMax® Tension Tie with 2-1/2" Screws is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the deck joists, rather than to the rim joist alone, the connection is stronger than typical through-bolt installations and complies with IRC and IBC code requirements regarding handrail and guardrail post connections for decks. The DTT2Z also complies with the new IRC requirements for laterally tying the...

The Simpson Strong-Tie SDWS22512DBB .220 x 5-1/2" Outdoor Accents® structural wood screw reduces installation time by driving easily without pre-drilling. When combined with the patent-pending,...

The Simpson Strong-Tie SDWS22512DBB .220 x 5-1/2" Outdoor Accents® structural wood screw reduces installation time by driving easily without pre-drilling. When combined with the patent-pending, load-rated Outdoor Accents STN22 structural washer, the solution delivers the decorative appearance of a bolt connection but with a much easier installation. The structural screw and washer are sold separately from each other and from the Outdoor Accents connectors. The screw's bold thread design...

The Simpson Strong-Tie A34SS Stainless Steel Framing Clips for wood to wood connections at a 90° angle. Stainless Steel material provides excellent corrosion resistance in highly corrosive...

The Simpson Strong-Tie A34SS Stainless Steel Framing Clips for wood to wood connections at a 90° angle. Stainless Steel material provides excellent corrosion resistance in highly corrosive environments. Length: 2-1/2" Finish: Type 316L Stainless Steel Flange Widths: 1-7/16" Fasteners: (8) 8d x 1-1/2" A34SS Information and Installation Instructions Type 316L Connector Stainless Steel Information Type 316L stainless steel is a nickel-chromium austenitic grade of stainless steel with 2-3%...

Simpson Strong Tie LUS24-2 Double 2 x 4 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also...

Simpson Strong Tie LUS24-2 Double 2 x 4 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS24-2 hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 3-1/8" (Height) x 2" (Seat Depth)...