Login/Register
Shopping Cart
OR
The Simpson Strong-Tie ABW44RZ for rough 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above...
The Simpson Strong-Tie ABW44RZ for rough 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW44RZ...
The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie...
The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie addresses a 2015 International Residential Code provision (section R507.2.4) that now allows four 750 lb. lateral connectors to be fastened to framing in the house with a lag screw. This provision is an alternative to using two 1,500 lb. lateral connections from the deck to the floor joists within the...
Save by Purchasing a Quantity of 15 Boxes (150 Pieces)! Simpson Strong-Tie PBS44AZ Standoff Post Bases are used to connect a 4 x 4 (3-1/2" x 3-1/2") to a concrete slab. The 1" standoff keeps the...
Save by Purchasing a Quantity of 15 Boxes (150 Pieces)! Simpson Strong-Tie PBS44AZ Standoff Post Bases are used to connect a 4 x 4 (3-1/2" x 3-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over time. ZMax® coating provides additional protection from the weather elements. Finish: ZMax® Base Material: 12 Gauge Base Dimensions: 3-9/16" x 3-1/2" Strap Material: 14 Gauge Strap Height: 6-1/4" Fastener Options: (14) 16d (2) 1/2"...
Save by Purchasing a Quantity of 10 Boxes (100 Bases)! Simpson Strong-Tie CB44 column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed...
Save by Purchasing a Quantity of 10 Boxes (100 Bases)! Simpson Strong-Tie CB44 column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 2" Wide Galvanized Steel Base Material: 7 Ga Galvanized (3-9/16" x 3-9/16") Fasteners: (2) 5/8" Machine Bolts CB44 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Save by Purchasing a Quantity of 10 Boxes (60 Pieces)! The Simpson Strong-Tie HDQ8-SDS3 holdown combines low deflection and high loads with ease of installation. The unique seat design of the HDQ8...
Save by Purchasing a Quantity of 10 Boxes (60 Pieces)! The Simpson Strong-Tie HDQ8-SDS3 holdown combines low deflection and high loads with ease of installation. The unique seat design of the HDQ8 greatly minimizes deflection under load. (20) 3" SDS Simpson Strong-Tie® Strong-Drive® screws are included which install easily, reduces fastener slip and provide a greater net section area of the post when compared to bolts. They may be installed either flush or raised off the mudsill...
Save by Purchasing a Quantity of 6 Boxes (72 Pieces)! The Simpson CBSQ44-SDS2 (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using...
Save by Purchasing a Quantity of 6 Boxes (72 Pieces)! The Simpson CBSQ44-SDS2 (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 4 x 4 Nominal (3-1/2" x 3-1/2") Base: 12 Ga. (3-9/16" x 3-1/2") Strap: 10 Ga. x 2-1/4"...
Simpson Strong-Tie EPB44 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying...
Simpson Strong-Tie EPB44 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and un-braced carports. Finish: Simpson Gray Paint Pipe Size: 1-1/16" OD x 8" Length Base Size:...
Save by Purchasing a Quantity of 36 Boxes (360 Pieces)! The Simpson PB44 Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to...
Save by Purchasing a Quantity of 36 Boxes (360 Pieces)! The Simpson PB44 Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Common Nails PB44 information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of...
Save by Purchasing a Quantity of 12 Boxes (240 Pieces)! Simpson Strong-Tie HDU2-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to...
Save by Purchasing a Quantity of 12 Boxes (240 Pieces)! Simpson Strong-Tie HDU2-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (6) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 14 Gauge Steel Finish: Standard...
Simpson Strong-Tie HD3BHDG Hot Dipped Galvanized Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other...
Simpson Strong-Tie HD3BHDG Hot Dipped Galvanized Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other lateral applications. The holdown must be attached to the receiving member with 5/8" machine bolts. A minimum wood member thickness of 1-1/2" is required to reach the least allowable tension load. The bottom stud hole is 4-3/4" above the plate line so you can install the holdown flush with the plate...
The Simpson MIU1.81/11 hanger is designed to hang 1-3/4" x 11-7/8" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU1.81/11 features...
The Simpson MIU1.81/11 hanger is designed to hang 1-3/4" x 11-7/8" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU1.81/11 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
Simpson Strong-Tie IUS1.81/11.88 is used to install 1-3/4" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging...
Simpson Strong-Tie IUS1.81/11.88 is used to install 1-3/4" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-7/8" (Wide) x 11-7/8" (Height) x 2" (Seat Depth) Fastener Options : (10) .148 x 3" Nails (Face) IUS1.81/11.88 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...
Simpson Strong-Tie HTU26-2 Double 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26-2 hanger very versatile for...
Simpson Strong-Tie HTU26-2 Double 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26-2 hanger very versatile for various trusses. Additionally you can have the HTU26-2 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is...
Simpson Strong Tie HUCQ1.81/11-SDS 1-3/4" Wide x 11" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/11-SDS hangers with...
Simpson Strong Tie HUCQ1.81/11-SDS 1-3/4" Wide x 11" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/11-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-3/4" (Wide) x 11" (Height) x 3" (Seat Depth) Included Fasteners: (10) SDS 1/4" x 1-3/4" Screws (Header) (4) SDS 1/4" x 1-3/4"...
The Simpson Strong-Tie HU24TF is a hybrid 2 x 4 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that...
The Simpson Strong-Tie HU24TF is a hybrid 2 x 4 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-7/16" (Height) x 2-1/4" (Seat Depth) x 2-7/16" (Top Flange) Fasteners: (6)...
Simpson Strong Tie U24R Rough 2 x 4 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U24R Rough 2 x 4 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/16" (Wide) x 3-5/8" (Height) x 2" (Seat Depth) Fastener Options: (4) .162" x 3-1/2" 16d Nails (Header) (2) .148" x 1-1/2" 10d Nails (Joist) U24R Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
Simpson Strong Tie HGUS26-2 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-2 hangers are...
Simpson Strong Tie HGUS26-2 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-2 hangers are designed to accept two 2 x 6 truss plates or joists with a minimum heel height of 4-5/16". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-5/16" (Wide) x 5-7/16" (Height) x 4" (Seat Depth) Fastener Options: (20) 16d Nails (Header) (8) 16d Nails (Joist)...Shorter Nails Not Allowed...
Save by Purchasing a Quantity of 24 Boxes (1200 Pieces)! Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points...
Save by Purchasing a Quantity of 24 Boxes (1200 Pieces)! Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS26 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized...
Simpson Strong Tie HUS26Z ZMax® 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...
Simpson Strong Tie HUS26Z ZMax® 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS26 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-5/8" (Wide) x 5-3/8" (Height) x 3"...
Simpson Strong Tie HGUS26-3 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-3 hangers are...
Simpson Strong Tie HGUS26-3 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-3 hangers are designed to accept three 2 x 6 truss plates or joists with a minimum heel height of 4-5/16". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 4-15/16" (Wide) x 5-1/2" (Height) x 4" (Seat Depth) Fastener Options: (20) 16d Nails (Header) (8) 16d Nails (Joist)...Shorter Nails Not Allowed...
Simpson Strong Tie HU26 2 x 4/6 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HU26 2 x 4/6 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/16" (Height) x 2-1/4" (Seat Depth) Fasteners: (4) .162 x 3-1/2" (16d) Nails (Header) (2) .148 x 1-1/2" (10d) Nails (Joist) HU26 Information and...
Simpson Strong Tie U24-2 Double 2 x 4 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U24-2 Double 2 x 4 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 3" (Height) x 2" (Seat Depth) Fastener Options: (4) .162" x 3-1/2" 16d Nails (Header) (2) .148" x 3" 10d Nails (Joist) U24-2 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...
The Simpson Strong-Tie HU26TF is a hybrid 2 x 6 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that...
The Simpson Strong-Tie HU26TF is a hybrid 2 x 6 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 5-3/8" (Height) x 2-1/4" (Seat Depth) x 2-7/16" (Top Flange) Fasteners: (10)...
Simpson Strong-Tie HTU28 2 x 8 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU28 hanger very versatile for various...
Simpson Strong-Tie HTU28 2 x 8 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU28 hanger very versatile for various trusses. Additionally you can have the HTU28 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is 1/8" per ASTM...