Simpson Strong-Tie

Simpson Strong-Tie ECC5 1/4-6 End Column Caps provide a high capacity connection between a 5-1/8" Glulam beam and a 6x post. ECC5 1/4-6 End Column Caps should be used when the 5-1/8" beam ends at...

Simpson Strong-Tie ECC5 1/4-6 End Column Caps provide a high capacity connection between a 5-1/8" Glulam beam and a 6x post. ECC5 1/4-6 End Column Caps should be used when the 5-1/8" beam ends at the 6x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/4" (Beam) x 5-1/2"...

The Simpson Strong-Drive® SDS25300 1/4" x 3" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25300 screw...

The Simpson Strong-Drive® SDS25300 1/4" x 3" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25300 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 3" Thread Length: 2" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive Type: 3/8"...

The Simpson Strong-Tie SSTB20L (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...

The Simpson Strong-Tie SSTB20L (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 24-5/8" Minimum Embedment: 16-5/8" Finish: None Rolled threads for higher...

Simpson Strong-Tie Avant Outdoor Accents® APVST412 Flat Straps bring decorative appeal and with structural strength to any outdoor living space like patio covers, gazebos and more. The APVST412...

Simpson Strong-Tie Avant Outdoor Accents® APVST412 Flat Straps bring decorative appeal and with structural strength to any outdoor living space like patio covers, gazebos and more. The APVST412 flat strap works for 4x lumber in both nominal and rough sizes. It can be used to connect two 4x beams together or add to any project as a decorative accent. These straps are easily installed with Outdoor Accents structural screws and hex-head washers. The Avant Collection features straight edges...

The Simpson Strong-Tie ML210Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood...

The Simpson Strong-Tie ML210Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood splitting and opposing hole patterns allow for back-to-back installation without fastener interference. Please Note: SDS screws are not included. Finish: ZMax® coating Material: 12 Gauge Fasteners (Not Included): (12) SDS25112 Screws Dimensions: 10" Length x 2" (Flange Widths) ML210Z Information...

Simpson Strong-Tie TA10ZKT Staircase Angles are used for securely providing support for stair treads eliminating the need for labor intensive notching of the stringer. Please Note: Kit includes two...

Simpson Strong-Tie TA10ZKT Staircase Angles are used for securely providing support for stair treads eliminating the need for labor intensive notching of the stringer. Please Note: Kit includes two (2) angles with ten (14) SDS25112 Screws Finish: ZMax® coating Material: 12 Gauge Fasteners (Not Included): (Min) SDS25112 Screws - (3) Stringer, (4) Tread (Max) SDS25112 Screws - (4) Stringer, (3) Tread Dimensions: 10-1/4" Length x 1-1/2" (Flange Width) TA10Z-R Information and Installation...

The Simpson Strong-Tie APDJT1.75-6 Deck Joist Tie attaches 1-3/4" beams to the side of 6x or larger support posts. It installs quickly and easily with the Outdoor Accents structural wood screw and...

The Simpson Strong-Tie APDJT1.75-6 Deck Joist Tie attaches 1-3/4" beams to the side of 6x or larger support posts. It installs quickly and easily with the Outdoor Accents structural wood screw and hex-head washer for the look of a bolted connection. Designed to meet stringent building codes for seismic or high-wind events Install with Outdoor Accents® structural wood screws and hex-head washers (sold separately) for a decorative look Material: 12 Gauge Steel Coating: ZMax® galvanized...

Simpson Strong-Tie SET-3G 22 oz. High-Strength Epoxy Adhesive is the latest innovation in epoxy anchoring adhesives that is formulated to provide superior performance in cracked and uncracked...

Simpson Strong-Tie SET-3G 22 oz. High-Strength Epoxy Adhesive is the latest innovation in epoxy anchoring adhesives that is formulated to provide superior performance in cracked and uncracked concrete at elevated temperatures. SET-3G installs and performs in a variety of environmental conditions and temperature extremes. The exceptional bond strength of SET-3G results in high design strengths. SET-3G dispenses as a 1:1 ratio in two-component producing a high-strength, epoxy-based anchoring...

Simpson Strong-Tie Mission Outdoor Accents® APB66DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APB66 or APB66R post base. These plates provide a...

Simpson Strong-Tie Mission Outdoor Accents® APB66DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APB66 or APB66R post base. These plates provide a finished look to an installed post base. These decorative side plates provide a black powder coat finish over ZMax® galvanization for extra corrosion resistance. Install these side plates with Outdoor Accents® SDWS22312DBB structural wood screws and STN22 hex-head washers (sold separately) for...

The Simpson Strong-Tie THD37212CS 3/8" x 2-1/2" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease...

The Simpson Strong-Tie THD37212CS 3/8" x 2-1/2" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of installation. Designed for use in dry, interior, noncorrosive environments or temporary outdoor applications, the countersunk Titen HD offers industry-leading performance even in seismic conditions. The countersunk head style is for applications that require a flush-mount profile. Countersinking...

Simpson Strong-Tie CNW7/8-5/8 coupling nuts are a tested and load rated method to join 7/8" threaded rod or anchor bolts to 5/8" rod extensions. The "witness" holes in the nut provide a means to...

Simpson Strong-Tie CNW7/8-5/8 coupling nuts are a tested and load rated method to join 7/8" threaded rod or anchor bolts to 5/8" rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW7/8-5/8 meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW7/8-5/8 Information and Data Standard G90 Zinc Galvanized Coating Information...

The THD37300HMG Mechanical Galvanized 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD...

The THD37300HMG Mechanical Galvanized 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced...

The Simpson Strong-Tie A35SS Stainless Steel Framing Clips exclusive bending slot allows instant, accurate field bends for all two- and three-way ties. Balanced, completely reversible design permits...

The Simpson Strong-Tie A35SS Stainless Steel Framing Clips exclusive bending slot allows instant, accurate field bends for all two- and three-way ties. Balanced, completely reversible design permits the A35SS Framing Clips to secure a great variety of wood-to-wood connections including joist-to-plate, studs-to-plate, joist-to-beams and ceiling joists-to beams. Type 316L stainless steel provides a high level of corrosion protection when required. Material: 18 Gauge Finish: Type 316L Stainless...

The Simpson Strong-Tie H2.5ASS Ties with 316L Stainless Steel Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5ASS Hurricane Ties connects the...

The Simpson Strong-Tie H2.5ASS Ties with 316L Stainless Steel Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5ASS Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. Material: 18 Gauge Finish: Type 316L Stainless Steel Fasteners: (10) 8d x 1-1/2" Nails H2.5ASS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L...

The Simpson Strong-Tie SP1Z ZMax® Stud Plate Tie is designed for sill-to-stud connections to resist uplift. The SP1 stud plate ties features angled holes for a positive connection from the stud...

The Simpson Strong-Tie SP1Z ZMax® Stud Plate Tie is designed for sill-to-stud connections to resist uplift. The SP1 stud plate ties features angled holes for a positive connection from the stud to the plates. ZMax® coating provides extra corrosion resistance when used in more corrosive environments. Features embossments that strengthen the stud-to-plate connection Designed to resist wind and seismic forces Can be used before or after installation including in retrofit applications...

The Simpson Strong-Tie MTSM16 offers moderate-strength truss-to-masonry connections. This twist strap has a small bend section to reduce interference at the transition points between the two...

The Simpson Strong-Tie MTSM16 offers moderate-strength truss-to-masonry connections. This twist strap has a small bend section to reduce interference at the transition points between the two members. The MTSM is load rated for installation on both grout-filled CMU (GFCMU) and concrete. Straps do not need to be wrapped over the truss to achieve the allowable load Can be field bent once to a 45° angle Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 16" (Length)...

The Simpson Strong-Tie PAB5-12-HDG 5/8" x 12" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...

The Simpson Strong-Tie PAB5-12-HDG 5/8" x 12" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...

Save by Purchasing a Pallet of 44 Boxes! Simpson Strong-Tie MASAPZ ZMaz®anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAPZ...

Save by Purchasing a Pallet of 44 Boxes! Simpson Strong-Tie MASAPZ ZMaz®anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAPZ is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAPZ version is used for installation on panelized forms. This anchor featured ZMax® coating when additional corrosion resistance is needed. Attaches easily to the concrete...

The S/HD10B Simpson Strong-Tie bolt-on holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD10B...

The S/HD10B Simpson Strong-Tie bolt-on holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD10B is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. Designed for installation with bolts into the studs or column. Can be installed directly on the base track or raised...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8 Information and Installation Instructions. Gray Paint Coating Information...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! Simpson Strong-Tie HDU5-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! Simpson Strong-Tie HDU5-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (14) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 14 Gauge Steel Finish: Standard G90...

Save by Purchasing a Quantity of 10 Boxes (60 Pieces)! The Simpson CBSQ66-SDS2 (for 5-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to...

Save by Purchasing a Quantity of 10 Boxes (60 Pieces)! The Simpson CBSQ66-SDS2 (for 5-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 6 x 6 Nominal (5-1/2" x 5-1/2") Base: 12 Ga. (5-1/2" x 5-1/2") Strap: 10 Ga. x 3" Wide x...

Save by Purchasing a Quantity of 15 Boxes (150 Pieces)! The Simpson PB66 Post Base for 6 x 6 (5-1/2" x 5-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to...

Save by Purchasing a Quantity of 15 Boxes (150 Pieces)! The Simpson PB66 Post Base for 6 x 6 (5-1/2" x 5-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fastener Options: (12) 16d Nails (2) 1/2" Diameter Machine Bolts PB66 information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

The Simpson Strong-Tie HU210-2TF is a hybrid 2 x 10-2 double hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features...

The Simpson Strong-Tie HU210-2TF is a hybrid 2 x 10-2 double hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 9-1/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top...