Simpson Strong-Tie

The Simpson Strong-Tie LTP4 Lateral Tie Plate transfers shear forces for top plate-to-rim joist or blocking connections. Nail holes are spaced to prevent wood splitting for single and double top...

The Simpson Strong-Tie LTP4 Lateral Tie Plate transfers shear forces for top plate-to-rim joist or blocking connections. Nail holes are spaced to prevent wood splitting for single and double top plate applications. May be installed over plywood sheathing. Material: 20 Gauge Finish: Standard G90 Length: 4-1/4" Width: 3" Fasteners: (12) 8d x 1-1/2" (12) SD #9 x 1-1/2" LTP4 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

The Simpson Strong-Tie H2A Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2A installation ties the rafter...

The Simpson Strong-Tie H2A Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2A installation ties the rafter to the stud while spanning a top plate. The Simpson H2A requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (12) 8d x 1-1/2" Nails H2A Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

Simpson Strong-Tie LCE4's universal design provides high capacity while eliminating the need for rights and lefts. For use with 4x or 6x lumber. LCE4's can be used as an end post cap application or...

Simpson Strong-Tie LCE4's universal design provides high capacity while eliminating the need for rights and lefts. For use with 4x or 6x lumber. LCE4's can be used as an end post cap application or an outside corner installation. Sold By The Each Material: 20 Gauge Finish: Standard G90 Galvanized Fastener Options: (24) 16d (24) SD10 x 1-1/2" LCE4 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of...

Simpson Strong Tie W1 Wedges are designed to be used with the Simpson Wedge Form Ties when forming low foundation walls. Two (2) W1 wedges are required for each wedge form tie used. Refer to...

Simpson Strong Tie W1 Wedges are designed to be used with the Simpson Wedge Form Ties when forming low foundation walls. Two (2) W1 wedges are required for each wedge form tie used. Refer to technical bulletin T-WT for recommended spacing. Explanation of "Stock" Availability Term Stock items are products we normally have available for immediate shipment either from our warehouse or our vendor's warehouse. If we or our vendor are out of stock or do not have enough inventory to complete your...

Simpson Strong-Tie CB66 column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66 base is installed during the pouring of the concrete. Strap Material: 7...

Simpson Strong-Tie CB66 column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66 base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 3" Wide Galvanized Steel Base Material: 7 Ga Galvanized (5-1/2" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB66 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface...

Simpson Strong-Tie Avant Outdoor Accents® APVB66R post bases secure a rough 6 x 6 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other...

Simpson Strong-Tie Avant Outdoor Accents® APVB66R post bases secure a rough 6 x 6 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported structures. These post bases feature a clean, simple design and provide ZMAX® galvanization with black powder coat for extra corrosion resistance. APVB66R bases include a 1" standoff from the concrete to help avoid post-end rot caused by moisture. The Avant Collection features straight edges...

Simpson Strong-Tie Avant Outdoor Accents® APST610 Flat Straps bring decorative appeal and with structural strength to any outdoor living space like patio covers, gazebos and more. The APVST610...

Simpson Strong-Tie Avant Outdoor Accents® APST610 Flat Straps bring decorative appeal and with structural strength to any outdoor living space like patio covers, gazebos and more. The APVST610 flat strap works for 4x lumber in both nominal and rough sizes. It can be used to connect two 6x beams together or add to any project as a decorative accent. These straps are easily installed with Outdoor Accents structural screws and hex-head washers. The Avant Collection features straight edges and...

Simpson Strong-Tie MSTA21Z ZMax® 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of...

Simpson Strong-Tie MSTA21Z ZMax® 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 18 gauge Finish: ZMax® G185 Galvanized Dimensions: 1-1/4" (Wide) x 21" (Length) Fasteners: (16) 10d Nails (16) SD9 x...

The Simpson PB66R Post Base for 6 x 6 (6" x 6") rough lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater...

The Simpson PB66R Post Base for 6 x 6 (6" x 6") rough lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fastener Options: (12) 16d Nails (2) 1/2" Diameter Machine Bolts PB66R information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...

The Simpson Strong-Tie SSTB20LHDG Hot Dipped Galvanized (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...

The Simpson Strong-Tie SSTB20LHDG Hot Dipped Galvanized (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 24-5/8" Minimum Embedment: 16-5/8" Finish: Hot...

The Simpson Strong-Tie THD37300CS 3/8" x 3" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of...

The Simpson Strong-Tie THD37300CS 3/8" x 3" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of installation. Designed for use in dry, interior, noncorrosive environments or temporary outdoor applications, the countersunk Titen HD offers industry-leading performance even in seismic conditions. The countersunk head style is for applications that require a flush-mount profile. Countersinking also...

The Simpson Strong-Tie APDJT2R-6 Deck Joist Tie attaches 2x rough joists to the side of 6x or larger support posts. It installs quickly and easily with the Outdoor Accents structural wood screw and...

The Simpson Strong-Tie APDJT2R-6 Deck Joist Tie attaches 2x rough joists to the side of 6x or larger support posts. It installs quickly and easily with the Outdoor Accents structural wood screw and hex-head washer for the look of a bolted connection. Designed to meet stringent building codes for seismic or high-wind events Install with Outdoor Accents® structural wood screws and hex-head washers (sold separately) for a decorative look Material: 12 Gauge Steel Coating: ZMax® galvanized...

The THD37400HMG Mechanical Galvanized 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD...

The THD37400HMG Mechanical Galvanized 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced...

Simpson Strong Tie LUS26-2SS Type 316L Stainless Steel 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for...

Simpson Strong Tie LUS26-2SS Type 316L Stainless Steel 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS26-2SS Double 2 x 6 Hangers are also approved for installation with SD10 Structural Screws. Material: 18 gauge Finish: Type 316L Stainless Steel Dimensions: 3-1/8" (Wide) x...

Simpson Strong-Tie LU28R-18 rough 2 x 8 Joist Hangers are an economical and time saving solution to securely installing rough 2 x 8 joists to a wood ledger or beam. You can install LU28R-18 hangers...

Simpson Strong-Tie LU28R-18 rough 2 x 8 Joist Hangers are an economical and time saving solution to securely installing rough 2 x 8 joists to a wood ledger or beam. You can install LU28R-18 hangers with 10d ,16d nails or #9 Strong-Drive® screws depending on the load value you are trying to achieve. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2" (Wide) x 6-3/8" (Height) x 1-1/2" (Seat Depth) Fastener Options: (8) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 1-1/2" 10d...

The Simpson Strong-Tie RTC2Z ZMax® Rigid Tie® Corner Connector is a uniquely designed rigid tie connector that connects two 2x horizontal members at a corner to a vertical 2 x 4 wood post....

The Simpson Strong-Tie RTC2Z ZMax® Rigid Tie® Corner Connector is a uniquely designed rigid tie connector that connects two 2x horizontal members at a corner to a vertical 2 x 4 wood post. Manufactured to high-quality standards to ensure solid performance, this corner rigid tie connector features a ZMax® galvanized finish for added corrosion resistance. Fastens with Simpson Strong-Tie® Strong-Drive® SD screws (not included) Constructed from corrosion-resistant galvanized...

Simpson Strong-Tie HL43PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL43PC to connect lumber to concrete...

Simpson Strong-Tie HL43PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL43PC to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Standard G90 Zinc Coating with a Black Powder Coat provides a low level of corrosion resistance. Material: 3 gauge Finish: Standard G90 Zinc Coating with a Black Powder Coat Dimensions: 4-1/4" (W1) x 4-1/4" (W2) x 3" (L) Bend to Hole Center: 2-3/4" Bolt...

The Simpson Strong-Tie MASB is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced...

The Simpson Strong-Tie MASB is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced anchor bolts. The MASB easily installs into wet concrete-grouted CMU block for a time-saving alternative to anchor bolts. Offset design for use in concrete block applications One-piece design, so there are no nuts and washers to lose Unique design eliminates concerns about stud placement 16 gauge...

The Simpson Strong-Tie SP2Z ZMax® Stud Plate Tie is designed for double-top-plate-to-stud connection to resist uplift. The SP2Z stud plate ties features angled holes for a positive connection...

The Simpson Strong-Tie SP2Z ZMax® Stud Plate Tie is designed for double-top-plate-to-stud connection to resist uplift. The SP2Z stud plate ties features angled holes for a positive connection from the stud to the plates. ZMax® coating provides extra corrosion resistance when used in more corrosive environments. Features embossments that strengthen the stud-to-plate connection Designed to resist wind and seismic forces Can be used before or after installation including in retrofit...

The Simpson Strong-Tie CHC Component Hoist Clip provides a tested, load-rated solution for the safe lifting and placement of assembled wood components. The CHC is load rated with Strong-Drive®...

The Simpson Strong-Tie CHC Component Hoist Clip provides a tested, load-rated solution for the safe lifting and placement of assembled wood components. The CHC is load rated with Strong-Drive® SDS Heavy-Duty Connector screws for easy installation and removal, and superior shear and withdrawal strength during lifting. Material: 12 Gauge Finish: Standard G90 Zinc Fastener Options: (2) SDS25300 Screws (Top) (3) SDS25300 Screws (Face) CHC Information and Installation Instructions. Standard G90...

The Simpson Strong-Tie PAB5-18 5/8" x 18" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and...

The Simpson Strong-Tie PAB5-18 5/8" x 18" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from high strength steel for higher load values. Please call our sales department direct at 800-323-2999 for pricing and...

The Simpson Strong-Tie HTSM16 14ga. x 16" Medium Twist Strap Masonry Tie offers moderate-strength truss-to-masonry connections. This twist strap has a small bend section to reduce interference at...

The Simpson Strong-Tie HTSM16 14ga. x 16" Medium Twist Strap Masonry Tie offers moderate-strength truss-to-masonry connections. This twist strap has a small bend section to reduce interference at the transition points between the two members. The HTSM is load rated for installation on both grout-filled CMU (GFCMU) and concrete. Straps do not need to be wrapped over the truss to achieve the allowable load Can be field bent once to a 45° angle Material: 14 gauge Finish: Standard G90...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH48-8/3 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH48-8/3 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 4-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8/3 Information and Installation Instructions. Gray Paint Coating Information...

Save by Purchasing a Quantity of 8 Boxes (128 Pieces)! The Simpson Strong-Tie HTT4 Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. This tension...

Save by Purchasing a Quantity of 8 Boxes (128 Pieces)! The Simpson Strong-Tie HTT4 Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. HTT4 Tension Ties are designed to be used in both in vertical and horizontal applications. Strap Material: 11 Gauge Finish: Standard G90 Zinc...