Login/Register
Shopping Cart
OR
Filter
Sort By
The S/HD15S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15S is...
The S/HD15S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15S is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. The S/HD15S has been designed to utilize fewer fasteners and reduce installation time. Can be installed directly on the base...
Simpson Strong-Tie CB66HDG Hot Dipped Galvanized column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66HDG base is installed during the pouring of the...
Simpson Strong-Tie CB66HDG Hot Dipped Galvanized column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66HDG base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 3" Wide Hot Dipped Galvanized Steel Base Material: 7 Ga Hot Dipped Galvanized (5-1/2" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB66HDG Information and Installation Instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the...
Save by Purchasing a Quantity of 12 Boxes (72 Pieces)! Simpson Strong-Tie HDU8-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to...
Save by Purchasing a Quantity of 12 Boxes (72 Pieces)! Simpson Strong-Tie HDU8-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (20) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 10 Gauge Steel Finish: Standard...
The S/HD15B Simpson Strong-Tie bolt-on holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15B...
The S/HD15B Simpson Strong-Tie bolt-on holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15B is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. Designed for installation with bolts into the studs or column. Can be installed directly on the base track or raised...
Simpson Strong-Tie CB66PC Powder Coat column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB base is installed during the pouring of the concrete. This...
Simpson Strong-Tie CB66PC Powder Coat column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB base is installed during the pouring of the concrete. This column base features a black powder-coat finish for a more decorative look. Strap Material: 7 Ga. x 3" Wide Black Powder Coat Steel Base Material: 7 Ga Powder Coat (5-1/2" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB66PC Information and Installation Instructions Simpson Strong-Tie Powder Coating...
The Simpson CBSQ88-SDS2 (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post...
The Simpson CBSQ88-SDS2 (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 8 x 8 Nominal (7-1/2" x 7-1/2") Base: 12 Ga. (7-1/2" x 7-3/8") Strap: 8 Ga. x 3" Wide x 8-11/16" High CBSQ88 Information and Installation...
Simpson Strong-Tie HDU8-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come...
Simpson Strong-Tie HDU8-SDS2.5HDG Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (20) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Hot Dipped Galvanized holdowns should be used when the application in...
The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the...
The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. Using a BP58-2 bearing plate installed in the seat of the HTT5 provides add more allowable tension load to the connection. HTT5 Tension Ties are designed to be used in both in vertical and...
The Simpson Strong-Tie LMA4Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x4 or 3x4 mudsills. The unique design provides installation...
The Simpson Strong-Tie LMA4Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x4 or 3x4 mudsills. The unique design provides installation flexibility, eliminating problems associated with wall framing alignment interfering with foundation anchors. The LMA4Z has a ZMax® coating, a thicker galvanized finish that helps extend the service life of the connector. Suitable for stem wall or slab foundations One-piece design, so there are no nuts...
The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum Embedment: 20-5/8" Finish: None Rolled threads for higher...
The Simpson CBSQ88-SDS2HDG Hot Dipped Galvanized (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1"...
The Simpson CBSQ88-SDS2HDG Hot Dipped Galvanized (for 7-1/2" x 7-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Hot Dipped Galvanizing provides added corrosion protection Easier Installation Higher Loads Hot Dipped Galvanized Column Size: 8 x 8 Nominal (7-1/2" x 7-1/2") Base: 12 Ga. (7-1/2" x 7-3/8")...
Save by Purchasing a Quantity of 12 Boxes (120 Pieces)! The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This...
Save by Purchasing a Quantity of 12 Boxes (120 Pieces)! The Simpson Strong-Tie HTT5 Tension Tie have three fastener options to provide much higher load values than its HTT20 predecessor. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. Using a BP58-2 bearing plate installed in the seat of the HTT5 provides add more allowable tension load to the connection. HTT5 Tension Ties...
The Simpson Strong-Tie LMA6Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x6 or 3x6 mudsills. The unique design provides installation...
The Simpson Strong-Tie LMA6Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x6 or 3x6 mudsills. The unique design provides installation flexibility, eliminating problems associated with wall framing alignment interfering with foundation anchors. The LMA6Z has a ZMax® coating, a thicker galvanized finish that helps extend the service life of the connector. Suitable for stem wall or slab foundations One-piece design, so there are no nuts...
The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
Save by Purchasing a Quantity of 500 SSTB24 Bolts! The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall...
Save by Purchasing a Quantity of 500 SSTB24 Bolts! The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum...
Simpson Strong-Tie CB68 column bases are used to provide a connection of a 6 x 8 (5-1/2" x 7-1/2") post to concrete. The CB68 base is installed during the pouring of the concrete. Strap Material: 7...
Simpson Strong-Tie CB68 column bases are used to provide a connection of a 6 x 8 (5-1/2" x 7-1/2") post to concrete. The CB68 base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 3" Wide Galvanized Steel Base Material: 7 Ga Galvanized (5-1/2" x 7-1/2") Fasteners: (2) 5/8" Machine Bolts CB68 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface...