Login/Register
Shopping Cart
OR
Simpson Strong Tie LUS414 4 x 12/14 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also...
Simpson Strong Tie LUS414 4 x 12/14 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS414 4 x 12/14 Hangers are approved for installation with 16D nails only. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 10-3/4" (Height) x 2" (Seat Depth) Fastener...
Simpson Strong Tie HUC310 3 x 10 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HUC310 3 x 10 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Reversed flanges allow you to hang joist or beams flush at corners or any other location where outside flanges will not work. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 8-7/8" (Height) x 2-1/2" (Seat...
The THD75812H 3/4" x 8-1/2" (5/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the...
The THD75812H 3/4" x 8-1/2" (5/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques....
The THD75100H 3/4" x 10" (5/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal...
The THD75100H 3/4" x 10" (5/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The...
Simpson Strong Tie LUS414Z ZMax® 4 x 12/14 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength....
Simpson Strong Tie LUS414Z ZMax® 4 x 12/14 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS414Z 4 x 12/14 Hangers are approved for installation with 16D nails only. Material: 18 gauge Finish: ZMax® G-185 Galvanized Dimensions: 3-9/16" (Wide) x 10-3/4" (Height) x 2" (Seat...
The Simpson Strong-Tie 5" x 11-7/8" MIT311.88-2 Double I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not...
The Simpson Strong-Tie 5" x 11-7/8" MIT311.88-2 Double I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...
Simpson Strong Tie HU310-2 Double 3 x 10 Standard Inverted Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for...
Simpson Strong Tie HU310-2 Double 3 x 10 Standard Inverted Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC310-2 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Low Dimensions: 5-1/8" (Wide) x 8-9/16" (Height) x 2-1/2" (Seat...
The Simpson Strong-Tie SUL2.37/9 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUL2.37/9 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-3/8" (Wide) x 8-15/16" (Height) x 1-5/16" (Outside Flange) x 2-1/8"...
The Simpson Strong-Tie SUL2.37/11 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUL2.37/11 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-3/8" (Wide) x 11-3/16" (Height) x 1-5/16" (Outside Flange) x 2-1/8"...
The Simpson Strong-Tie 5" x 14" MIT314-2 Double I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but...
The Simpson Strong-Tie 5" x 14" MIT314-2 Double I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90 Galvanized...
Simpson Strong Tie HU312 3 x 12 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HU312 3 x 12 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 10-5/8" (Height) x 2-1/2" (Seat Depth) Fastener Options: (16) .162 x 3-1/2" (16d) Nails (Header) (6) .148 x 1-1/2" (10d) Nails (Joist) HU312 Information and...
The Simpson Strong-Tie SUL2.37/11 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 14" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUL2.37/11 Skewed 45° Left Hanger can be used when hanging a 2-1/4" or 2-5/16" x 14" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 14" engineered wood joist end may be square or beveled cut. This hanger can be used for hanging 2-1/4" or 2-5/16" x 16" engineered wood joists with a required web stiffener. Material: 16 gauge Finish:...
Simpson Strong Tie HU312-2 Double 3 x 12 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HU312-2 Double 3 x 12 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU312-2 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Low Dimensions: 5-1/8" (Wide) x 10-13/16" (Height) x 2-1/2" (Seat Depth)...
The Simpson Strong-Tie SUR2.37/9 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUR2.37/9 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 9-1/2" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-3/8" (Wide) x 8-15/16" (Height) x 1-5/16" (Outside Flange) x 2-1/8"...
Simpson Strong Tie HUC312 3 x 12 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HUC312 3 x 12 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Reversed flanges allow you to hang joist or beams flush at corners or any other location where outside flanges will not work. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 10-5/8" (Height) x 2-1/2" (Seat...
The Simpson Strong-Tie SUR2.37/11 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist. The angles nail slots direct nails for proper...
The Simpson Strong-Tie SUR2.37/11 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 11-7/8" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-3/8" (Wide) x 11-3/16" (Height) x 1-5/16" (Outside Flange) x 2-1/8"...
Simpson Strong Tie HUC312-2 Double 3 x 12 Standard Inverted Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for...
Simpson Strong Tie HUC312-2 Double 3 x 12 Standard Inverted Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC312-2 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Low Dimensions: 5-1/8" (Wide) x 10-7/8" (Height) x 2-1/2"...
The Simpson Strong-Tie SUR2.37/11 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 14" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUR2.37/11 Skewed 45° Right Hanger can be used when hanging a 2-1/4" or 2-5/16" x 14" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/4" or 2-5/16" x 14" engineered wood joist end may be square or beveled cut. This hanger can be used for hanging 2-1/4" or 2-5/16" x 16" engineered wood joists with a required web stiffener. Material: 16 gauge Finish:...
Simpson Strong Tie HU314 3 x 14 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HU314 3 x 14 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 12-3/8" (Height) x 2-1/2" (Seat Depth) Fastener Options: (18) .162 x 3-1/2" (16d) Nails (Header) (8) .148 x 1-1/2" (10d) Nails (Joist) HU314 Information and...
Simpson Strong Tie HU314-2 3 x 14 Double Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HU314-2 3 x 14 Double Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU314-2 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/8" (Wide) x 12-5/8" (Height) x 2-1/2" (Seat Depth) Fastener...
The Simpson Strong-Tie SUL2.56/9 Skewed 45° Left Hanger can be used when hanging a 2-1/2" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation. These...
The Simpson Strong-Tie SUL2.56/9 Skewed 45° Left Hanger can be used when hanging a 2-1/2" x 9-1/2" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/2" x 9-1/2" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 8-13/16" (Height) x 1-1/8" (Outside Flange) x 2-1/8" (Inside Flange) Base:...
Simpson Strong Tie HUC314 3 x 14 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HUC314 3 x 14 Reversed Flange Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Reversed flanges allow you to hang joist or beams flush at corners or any other location where outside flanges will not work. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 12-3/8" (Height) x 2-1/2" (Seat...
Simpson Strong Tie HU316 3 x 16 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial...
Simpson Strong Tie HU316 3 x 16 Standard Face Mount Beam Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 14-1/8" (Height) x 2-1/2" (Seat Depth) Fastener Options: (20) .162 x 3-1/2" (16d) Nails (Header) (8) .148 x 1-1/2" (10d) Nails (Joist) HU316 Information and...
The Simpson Strong-Tie SUL2.56/11 Skewed 45° Left Hanger can be used when hanging a 2-1/2" x 11-1/4" or 11-7/8" engineered wood joist. The angles nail slots direct nails for proper installation....
The Simpson Strong-Tie SUL2.56/11 Skewed 45° Left Hanger can be used when hanging a 2-1/2" x 11-1/4" or 11-7/8" engineered wood joist. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2-1/2" x 11-1/4" or 11-7/8" engineered wood joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-9/16" (Wide) x 11-3/16" (Height) x 1-1/8" (Outside Flange) x 2-1/8"...