Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson Strong-Tie SUR26Z Skewed Right 2 x 6/8 joist hangers with ZMax® coating are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will...
The Simpson Strong-Tie SUR26Z Skewed Right 2 x 6/8 joist hangers with ZMax® coating are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 6/8 joist end may be square or beveled cut. ZMax® coating provides additional corrosion protection when required. Material: 16 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-9/16" (Wide) x 5" (Height) x 1-1/8" (Outside...
Simpson Strong Tie U26-2 Double 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U26-2 Double 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 5" (Height) x 2" (Seat Depth) Fastener Options: (8) .162" x 3-1/2" 16d Nails (Header) (4) .148" x 3" 10d Nails (Joist) U26-2 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...
The Simpson Strong-Tie BA1.81/14 Top Flange Hanger is designed for 1-3/4" x 14" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn...
The Simpson Strong-Tie BA1.81/14 Top Flange Hanger is designed for 1-3/4" x 14" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn lumber and higher loads with engineered wood products. All BA hangers feature minimum nailing with positive-angle nailing (PAN) to target moderate load conditions and maximum nailing to support higher loads. Please Note: BA Hangers may be modified for slopes and/or skews up to 45°. The top flanges...
The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...
The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...
The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways:...
The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie HCJTZ with 3/4" x 4-3/4" pins can be used with a minimum beam size of 5-1/8" x 15". Minimum Beam Size: 5-1/8" x 15" Material: 10 Gauge Finish:...
Simpson Strong Tie face mount HU11 Composite Lumber Hanger is designed for hanging 1-3/4" x 11-1/4 or 11-7/8" Microllam® LVL beams. Filling all holes including triangle holes will give you...
Simpson Strong Tie face mount HU11 Composite Lumber Hanger is designed for hanging 1-3/4" x 11-1/4 or 11-7/8" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 11-1/16" (Height) x 2-1/2" (Seat Depth) Fastener Options: (22) 16d Nails (Header-Min) (6) 10d Nails (Joist-Min) (30) 16d Nails (Header-Max) (10) 10d Nails (Joist-Max) HU11 Information and Installation...
The Simpson Strong-Tie HU210TF is a hybrid 2 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing...
The Simpson Strong-Tie HU210TF is a hybrid 2 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 9-1/8" (Height) x 2-1/4" (Seat Depth) x 2-7/16" (Top Flange) Fasteners: (12)...
Simpson Strong Tie HUC26-3 Triple 2 x 6/8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HUC26-3 Triple 2 x 6/8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC26-3 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work. Material:...
Simpson Strong Tie HUCQ210-3Z-SDS ZMax®4-5/8" Wide Triple 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-3Z-SDS hangers with...
Simpson Strong Tie HUCQ210-3Z-SDS ZMax®4-5/8" Wide Triple 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-3Z-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: ZMax® G-185 Coating Dimensions: 4-5/8" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (12) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2"...
Simpson Strong Tie HUS28-2 Double 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also...
Simpson Strong Tie HUS28-2 Double 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 7-3/16" (Height) x 2" (Seat Depth) Fastener Options: (6) 16d Nails or SD10212 Screws(Header) (6) 16d Nails...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 9-1/2" (Height) x 2" (Seat Depth) Fastener Options : (8) .148 x 3" Nails (Face) IUS2.06/9.5 Information and Installation...
Simpson Strong Tie LUS26SS Type 316L Stainless Steel 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for...
Simpson Strong Tie LUS26SS Type 316L Stainless Steel 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS26SS hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 4-3/4" (Height)...
The Simpson Strong-Tie 2-5/16" x 11-7/8" MIT3511.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed,...
The Simpson Strong-Tie 2-5/16" x 11-7/8" MIT3511.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...
The Simpson MIU2.37/9 hanger is designed to hang 2-5/16" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU2.37/9 features...
The Simpson MIU2.37/9 hanger is designed to hang 2-5/16" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU2.37/9 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
The Simpson Strong-Tie SUR26SS Type 316L Stainless Steel Skewed Right 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers...
The Simpson Strong-Tie SUR26SS Type 316L Stainless Steel Skewed Right 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 6/8 joist end may be square or beveled cut. Stainless Steel provides additional corrosion protection when required. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 5" (Height) x 1-1/8" (Outside...
Simpson Strong Tie U26-3 Triple 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U26-3 Triple 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 4-5/8" (Wide) x 4-1/4" (Height) x 2" (Seat Depth) Fastener Options: (8) .162" x 3-1/2" 16d Nails (Header) (4) .148" x 3" 10d Nails (Joist) U26-3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...