Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson PB44HDG Hot Dipped Galvanized Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Hot...
The Simpson PB44HDG Hot Dipped Galvanized Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Hot Dipped Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Nails PB44HDG information and installation instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with...
Simpson Strong-Tie PBS46 Standoff Post Bases are used to connect a 4 x 6 (3-1/2" x 5-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over...
Simpson Strong-Tie PBS46 Standoff Post Bases are used to connect a 4 x 6 (3-1/2" x 5-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over time. Available only in standard galvanizing. Finish: Standard G90 Galvanized Base Material: 12 Gauge Base Dimensions: 3-9/16" x 5-7/16" Strap Material: 14 Gauge Strap Height: 6-9/16" Fastener Options: (14) 16d (2) 1/2" Machine Bolts Additional PBS46 information and installation instructions...
The geometry of the Simpson Strong-Tie SB7/8x24HDG 7/8" x 24" Hot Dipped Galvanized anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions...
The geometry of the Simpson Strong-Tie SB7/8x24HDG 7/8" x 24" Hot Dipped Galvanized anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 8" wide concrete stem wall without creating excessive horizontal forces. The SB7/8x24HDG is designed to maximize performance with minimum embedment of 18". Identification on the bolt head showing embedment angle and model Stamped embedment line...
The Simpson Strong-Tie SSTB16L (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The Simpson Strong-Tie SSTB16L (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 19-5/8" Minimum Embedment: 12-5/8" Finish: None Rolled threads for higher...
The Simpson CBSQ46-SDS2 (for 3-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post...
The Simpson CBSQ46-SDS2 (for 3-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 4 x 6 Nominal (3-1/2" x 5-1/2") Base: 12 Ga. (3-9/16" x 5-5/16") Strap: 10 Ga. x 3" Wide x 8-11/16" High CBSQ46 Information and Installation...
The Simpson Strong-Tie DTT2SS Type 316L Stainless Steel Tension Tie is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the deck...
The Simpson Strong-Tie DTT2SS Type 316L Stainless Steel Tension Tie is a safe, cost-effective way to attach deck-railing posts to the deck framing. Because the post is tied back into the deck joists, rather than to the rim joist alone, the connection is stronger than typical through-bolt installations and complies with IRC and IBC code requirements regarding handrail and guardrail post connections for decks. The DTT2SS also complies with the new IRC requirements for laterally tying the deck to...
Simpson Strong-Tie EPB44PHDG Hot Dipped Galvanized allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above concrete in both cast in place and retrofit applications. This clearance...
Simpson Strong-Tie EPB44PHDG Hot Dipped Galvanized allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above concrete in both cast in place and retrofit applications. This clearance allows the 4 x 4 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Hot...
The Simpson Strong-Tie HD7B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design...
The Simpson Strong-Tie HD7B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design as the HDQ8-SDS2.5 holdown that is proven to greatly reduce deflection while under load. All the HDB style holdown anchors are designed to provide loads for intermediate-load-range shearwalls, braced wall panels and lateral applications. The HD7B must be connected to a minimum of 3" of material....
Simpson Strong-Tie HDU4-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (10) 2-1/2" Simpson...
Simpson Strong-Tie HDU4-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (10) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 14 Gauge Steel Finish: Standard G90 Galvanized Anchor Bolt Diameter: 5/8" Pre-deflected...
Simpson Strong-Tie MASAZ ZMax® anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAZ is not only quick to install they also...
Simpson Strong-Tie MASAZ ZMax® anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAZ is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAZ version is used for installation on standards forms. Attaches easily to the concrete form for quick installation Lays flat on the form board so there is no anchor bolt to finish around No labor costs involved in...
The new patent-pending Simpson Strong-Tie® MPB88Z is the first post base specifically designed to provide moment resistance for 8 x 8 columns or posts. An innovative overlapping sleeve design...
The new patent-pending Simpson Strong-Tie® MPB88Z is the first post base specifically designed to provide moment resistance for 8 x 8 columns or posts. An innovative overlapping sleeve design encapsulates the post, helping to resist rotation around its base. The MPB88Z is ideal for outdoor structures, such as carports, fences and decks. Built-in standoff tabs provide the required 1" standoff to resist decay of the post while eliminating multiple parts and assembly. Additionally, the MPB88Z...
The Simpson Strong-Tie PAB4-30 1/2" x 30" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB4-30 1/2" x 30" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
The Simpson PB44R Post Base for rough 4 x 4 (4" x 4") lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater...
The Simpson PB44R Post Base for rough 4 x 4 (4" x 4") lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Common Nails PB44R information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating...
The S/HD8S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD8S is...
The S/HD8S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD8S is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. The S/HD8S has been designed to utilize fewer fasteners and reduce installation time. Can be installed directly on the base track...
The geometry of the Simpson Strong-Tie SB1x30 1" x 30" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into...
The geometry of the Simpson Strong-Tie SB1x30 1" x 30" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 8" wide concrete stem wall without creating excessive horizontal forces. The SB1x30 with a minimum embedment of 24" is intended to cover holdown devices that exceed the capacity of SSTB anchors. Identification on the bolt head showing embedment angle and model Stamped...
The SSTB16LHDG Hot Dipped Galvanized (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The SSTB16LHDG Hot Dipped Galvanized (5/8" Diameter by 19-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 19-5/8" Minimum Embedment: 12-5/8" Finish: Hot Dipped Galvanized...