Login/Register
Shopping Cart
OR
Simpson Strong-Tie HL76 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL76 to connect lumber to concrete using an a wedge...
Simpson Strong-Tie HL76 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL76 to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Please Note: This angle is available with a gusset, hot dipped galvanized or powder coating as a special order. Please call our sales department direct at 800-323-2999 for pricing and lead time. Material: 3 gauge Finish: Simpson Gray Dimensions: 7-1/4" (W1) x 7-1/4" (W2)...
The Simpson Strong-Tie SSTB28L (7/8" Diameter by 32-7/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The Simpson Strong-Tie SSTB28L (7/8" Diameter by 32-7/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 8" Bolt Diameter: 7/8" Overall Length: 32-7/8" Minimum Embedment: 24-7/8" Finish: None Rolled threads for higher...
Simpson Strong-Tie CC88 Column Caps provide a high capacity connection between a 8x beam and a 8x post. CC88 Column Caps should be used when the 8x beam extends through the 8x post. Please Note:...
Simpson Strong-Tie CC88 Column Caps provide a high capacity connection between a 8x beam and a 8x post. CC88 Column Caps should be used when the 8x beam extends through the 8x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 7-1/2" (Beam) x 7-1/2" (Post) x 13" (Length)...
Simpson Strong-Tie ITS2.56/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.56/9.5 installs 2-1/2" or 2-9/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP...
Simpson Strong-Tie ITS2.56/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.56/9.5 installs 2-1/2" or 2-9/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails...
Simpson Strong Tie HUCQ612-SDS 5-1/2" Wide 6 x 12 Heavy Duty Beam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to...
Simpson Strong Tie HUCQ612-SDS 5-1/2" Wide 6 x 12 Heavy Duty Beam Hangers come with the required SDS screws to reach the load values you require. HUCQ hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 5-1/2" (Wide) x 11" (Height) x 3" (Seat Depth) Included Fasteners: (14) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2" Screws (Joist) HUCQ612-SDS...
Simpson Strong-Tie CS20-R 20-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS20-R are approved for use with SD Screws as a nail...
Simpson Strong-Tie CS20-R 20-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS20-R are approved for use with SD Screws as a nail substitution. 25' packs are an economical choice when you do not require large amounts. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 25' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS20-R Information and...
The Simpson Strong-Tie SUR210-2 Skewed Right Double 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally...
The Simpson Strong-Tie SUR210-2 Skewed Right Double 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist ends may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 8-11/16" (Height) x 1-7/16" (Outside Flange) x 2-3/8" (Inside Flange) Fastener Options : (14) .162 x 3-1/2" Nails...
The Simpson Strong-Tie PAB6-18-HDG 3/4" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB6-18-HDG 3/4" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
Simpson Strong-Tie Avant Outdoor Accents® APVB1010R post bases secure a rough 10 x 10 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other...
Simpson Strong-Tie Avant Outdoor Accents® APVB1010R post bases secure a rough 10 x 10 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported structures. These post bases feature a clean, simple design and provide ZMAX® galvanization with black powder coat for extra corrosion resistance. APVB1010 bases include a 1" standoff from the concrete to help avoid post-end rot caused by moisture. The Avant Collection features straight...
Simpson Strong Tie HUC210-2Z ZMax® Double 2 x 10 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for...
Simpson Strong Tie HUC210-2Z ZMax® Double 2 x 10 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC210-2Z ZMax® hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges...
The THD50612H 1/2" x 6-1/2" (20/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the...
The THD50612H 1/2" x 6-1/2" (20/Box) Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques....
The Simpson Strong-Tie THD50800H6SS Type 316 Stainless Steel 1/2" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD50800H6SS Type 316 Stainless Steel 1/2" x 8" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie SPH8Z ZMax® Heavy U-Shaped Stud Plate Tie is designed as a stud-to-plate connection to resist roof uplift. This heavy U-shaped strap has a horizontal portion that bears...
The Simpson Strong-Tie SPH8Z ZMax® Heavy U-Shaped Stud Plate Tie is designed as a stud-to-plate connection to resist roof uplift. This heavy U-shaped strap has a horizontal portion that bears against the wood wall top plates or sill plates and two vertical legs that are nailed to the edges of a wood stud. This tie is a cost-effective option when properly installed before the placement of the wall. ZMax® coating provides corrosion resistance when required. Load rated Designed to resist...
Simpson Strong-Tie H8SS Type 316L Stainless Steel Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8SS Tie uses (10) 10d .148" x...
Simpson Strong-Tie H8SS Type 316L Stainless Steel Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8SS Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: Type 316L Stainless Steel Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8SS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L stainless steel is...
Simpson Strong-Tie CB88RHDG Hot Dipped Galvanized column bases are used to provide a connection of a rough 8 x 8 (8" x 8") post to concrete. The CB88RHDG base is installed during the pouring of the...
Simpson Strong-Tie CB88RHDG Hot Dipped Galvanized column bases are used to provide a connection of a rough 8 x 8 (8" x 8") post to concrete. The CB88RHDG base is installed during the pouring of the concrete. Coated hot dipped galvanized for additional corrosion resistance. Strap Material: 3 Ga. x 3" Wide Hot Dipped Galvanized Steel Base Material: 3 Ga Hot Dipped Galvanized (8" x 8") Fasteners: (2) 3/4" Machine Bolts CB88RHDG Information and Installation Instructions Hot Dipped Galvanized...
The Simpson Strong-Tie HUC410TF is a hybrid 4 x 10 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with...
The Simpson Strong-Tie HUC410TF is a hybrid 4 x 10 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two concealed flanges for end-of-wall or corner installation. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 9-1/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (14)...
Simpson Strong Tie U44R Rough 4 x 4 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U44R Rough 4 x 4 Standard Face Mount Beam Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 4-1/16" (Wide) x 2-5/8" (Height) x 2" (Seat Depth) Fastener Options: (4) .162 x 3-1/2" 16d Nails (Header) (2) .148 x 3" 10d Nails (Joist) U44R Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...
Save by Purchasing a Quantity of 54 Boxes (2700 Pieces)! Simpson Strong Tie LUS210 2 x 10/12 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two...
Save by Purchasing a Quantity of 54 Boxes (2700 Pieces)! Simpson Strong Tie LUS210 2 x 10/12 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS210 2 x 10/12 Hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized...
The Simpson Strong-Tie TNT25400TF Titen Turbo™ 1/4" x 4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...
The Simpson Strong-Tie TNT25400TF Titen Turbo™ 1/4" x 4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping and...
The Simpson Strong-Tie 2-1/2" x 24" HIT324 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...
The Simpson Strong-Tie 2-1/2" x 24" HIT324 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. The HIT also features extra triangle holes to allow higher uplift loads. Material: 16 gauge Finish: Standard G90 Galvanized...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.56/11.88 is used to install 2-1/2" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.56/11.88 is used to install 2-1/2" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-5/8" (Wide) x 11-7/8" (Height) x 2" (Seat Depth) Fastener Options : (10) .148 x 3" Nails (Face) IUS2.56/11.88 Information and Installation...
The Simpson MIU3.56/20 hanger is designed to hang 3-1/2" x 20" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU3.56/20 features positive-angle...
The Simpson MIU3.56/20 hanger is designed to hang 3-1/2" x 20" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU3.56/20 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
Simpson Strong-Tie ECCLR666HDG Hot Dipped Galvanized End Corner Column Caps provide a right connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Material: 7 gauge...
Simpson Strong-Tie ECCLR666HDG Hot Dipped Galvanized End Corner Column Caps provide a right connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Fasteners: (6) 5/8" x 7" Machine Bolt (Beam and Post) ECCLR666HDG Information and Installation Instructions. Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.56/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.56/9.5 installs 2-1/2" or 2-9/16" x 9-1/2"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.56/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.56/9.5 installs 2-1/2" or 2-9/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses...