Simpson Strong-Tie

The Simpson Strong-Tie SSTB24HDG Hot Dipped Galvanized (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...

The Simpson Strong-Tie SSTB24HDG Hot Dipped Galvanized (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum Embedment: 20-5/8" Finish: Hot...

Simpson Strong-Tie ECCQ5-6SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. ECCQ5-6SDS2.5 End Column Caps should be used when the beam ends at the...

Simpson Strong-Tie ECCQ5-6SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. ECCQ5-6SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ5-6SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call...

The Simpson Strong-Tie H3Z Clip with ZMax® Corrosion resistance is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A...

The Simpson Strong-Tie H3Z Clip with ZMax® Corrosion resistance is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3Z installation ties the single top plate to the rafter or truss. The Simpson H3Z requires (8) 8d joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (8) 8d x 2-1/2" Nails H3Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax®...

Simpson Strong-Tie MSTA30 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x...

Simpson Strong-Tie MSTA30 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 30" (Length) Fasteners: (22) 10d Nails (22) SD9 x 1-1/2" Screws...

The Simpson Strong-Tie SUL210Z Skewed Left 2 x 10/12 joist hangers with ZMax coating are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will...

The Simpson Strong-Tie SUL210Z Skewed Left 2 x 10/12 joist hangers with ZMax coating are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. ZMax coating provides additional corrosion protection when required. Material: 16 gauge Finish: ZMax G-185 Galvanized Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8" (Outside Flange) x...

The Simpson Strong-Tie LPC6Z design allows you the flexibility to connect a 6x or smaller width beam or joist to the top of a 6x post. Sold By Each Material: 16 Gauge Post Width: 5-1/2" Finish:...

The Simpson Strong-Tie LPC6Z design allows you the flexibility to connect a 6x or smaller width beam or joist to the top of a 6x post. Sold By Each Material: 16 Gauge Post Width: 5-1/2" Finish: ZMax® G-185 Galvanized Fasteners: (8) 10d (Beam) , (8) 10d (Post) LPC6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating) than the standard hot-dip galvanized coating (galvanized...

Simpson Strong-Tie LUC210Z ZMax® 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210Z also provides cleaner lines for exposed conditions...

Simpson Strong-Tie LUC210Z ZMax® 2 x 10/12 Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC210Z also provides cleaner lines for exposed conditions such as overhead decks. Material: 18 Gauge Finish: G-185 ZMax® Dimensions: 1-9/16" (Wide) x 7-3/4" (Height) x 1-3/4" (Seat Depth) Fastener Options: (10) .162 x 3-1/2" 16d Nails (Header) (6) .148 x 1-1/2" 10d Nails (Joist) Strong Drive® SD9112 #9 x 1-1/2" Structural Screws may be substituted...

The Simpson Strong-Tie Deck Drive™ DSVT3S #10 x 3" Tan Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start...

The Simpson Strong-Tie Deck Drive™ DSVT3S #10 x 3" Tan Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVT3S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber so...

Simpson Strong Drive® SSA10D 3" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as...

Simpson Strong Drive® SSA10D 3" x .148" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 67 nails in the 1 lb. pack. The nails are type 316 stainless steel providing high/severe corrosion protection. SSNA10D Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel chromium...

The 1-1/4" wide x 20" long LTS20 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist...

The 1-1/4" wide x 20" long LTS20 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 20" (Length) Fasteners: 10d or 10d x 1-1/2" depending on load value required and depth of receiving member (See...

The Simpson Strong-Tie 2-1/2" or 2-9/16" x 11-7/8" MIT311.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not...

The Simpson Strong-Tie 2-1/2" or 2-9/16" x 11-7/8" MIT311.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard...

The Simpson Strong-Tie Deck Drive™ DSVG212S #10 x 2-1/2" Gray Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...

The Simpson Strong-Tie Deck Drive™ DSVG212S #10 x 2-1/2" Gray Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVG212S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth...

The Simpson Strong-Drive® SDS25500 1/4" x 5" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25500 screw...

The Simpson Strong-Drive® SDS25500 1/4" x 5" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25500 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 5" Thread Length: 2-3/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive Type:...

Simpson Strong-Tie CS16 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16 are approved for use with SD Screws as a nail...

Simpson Strong-Tie CS16 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16 are approved for use with SD Screws as a nail substitution. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 150' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS16 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...

Simpson Strong-Tie CCQ5-6SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. CCQ5-6SDS2.5 Column Caps should be used when the beam extends through the...

Simpson Strong-Tie CCQ5-6SDS2.5 Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 6x post. CCQ5-6SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ5-6SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...

Simpson Strong-Tie HL53HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL53HDG to connect lumber...

Simpson Strong-Tie HL53HDG Hot Dipped Galvanized Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL53HDG to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Hot dipped galvanizing provide corrosion resistance from the elements or corrosive lumber. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 5-3/4" (W1) x 5-3/4" (W2) x 2-1/2" (L) Bolt Holes: (4) 1/2" HL53HDG Heavy Angle Information...

The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...

The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 28-1/8" Minimum Embedment: 20-5/8" Finish: None Rolled threads for higher...

Simpson Strong-Tie CCO9 End Column Caps with no post straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The CCO9 Column Caps comes with no coating to allow you...

Simpson Strong-Tie CCO9 End Column Caps with no post straps provides a high capacity connection between a 8-3/4" wide beam and a steel post. The CCO9 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 8-7/8" (Beam) x 13"...

Simpson Strong Tie HUS46 4 x 6 Double Shear Beam Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...

Simpson Strong Tie HUS46 4 x 6 Double Shear Beam Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 5" (Height) x 2" (Seat Depth) Fastener Options: (4) 16d Nails or SD10212 Screws(Header) (4) 16d Nails (Joist)...Shorter Nails...

Simpson Strong-Tie IUS2.37/11.88 is used to install 2-5/16" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging...

Simpson Strong-Tie IUS2.37/11.88 is used to install 2-5/16" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-7/16" (Wide) x 11-7/8" (Height) x 2" (Seat Depth) Fastener Options : (10) .148 x 3" Nails (Face) IUS2.37/11.88 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...

Simpson Strong-Tie ITS2.37/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.37/9.5 installs 2-5/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange...

Simpson Strong-Tie ITS2.37/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.37/9.5 installs 2-5/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the...

Simpson Strong-Tie Avant Outdoor Accents® APVB88 post bases secure a 8 x 8 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported...

Simpson Strong-Tie Avant Outdoor Accents® APVB88 post bases secure a 8 x 8 post or column to concrete and are perfect for outdoor projects such as pergolas, patio covers and other top-supported structures. These post bases feature a clean, simple design and provide ZMAX® galvanization with black powder coat for extra corrosion resistance. APVB88 bases include a 1" standoff from the concrete to help avoid post-end rot caused by moisture. The Avant Collection features straight edges and...

The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...

The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...

The Simpson Strong-Tie SUL210SS Type 316L Stainless Steel Skewed Left 2 x 10/12 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers...

The Simpson Strong-Tie SUL210SS Type 316L Stainless Steel Skewed Left 2 x 10/12 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. Stainless Steel provides additional corrosion protection when required. Material: 16 gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8"...