Questions?
Call Our Employee Owner
Sales Department Direct

800-323-2999

Bolts, Hex Nuts and Washers For Structural Connections


Products 49-96 of 129
Show
Plated Lag Screw
Bay Standard Mfg

More Information

Price: $0.72
Availability: Stock
Bay Standard Mfg Item #: LP1280 -

    These 1/2" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

    3/4" - 10 Zinc Plated Hex Nut
    Bay Standard Mfg

    More Information

    Price: $0.36
    Availability: Stock
    Bay Standard Mfg Item #: N34HDG -

      3/4" - 10 Hot Dipped Galvanized Hex Nuts for either 3/4" HDG machine bolts or all thread rod. Uses 1-1/8" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or threaded rod. Do not use on plain or zinc plated bolts.

      All Thread Extension Rods
      Bay Standard Mfg

      More Information

      Price: $1.62
      Availability: Stock
      Bay Standard Mfg Item #: ALLP5812 -

        These 5/8" x 12" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request

        7/8" Hex Plated Coupling Nut with Witness Hole
        Bay Standard Mfg

        More Information

        Price: $2.32
        Availability: Stock
        Bay Standard Mfg Item #: CPNW78 -

          7/8" x 2-1/2" (H) Witness Hole Coupling Nuts are used to connected two 7/8" threaded rods together or extend a 7/8" SSTB or standard anchor bolt. The witness hole allows the inspector to confirm the rods are connected properly. Zinc Plated Hex Head Imported

          Hex Head Zinc Plated Machine Bolt
          Bay Standard Mfg

          More Information

          Price: $0.74
          Availability: Stock
          Bay Standard Mfg Item #: MP5840 -

            These 5/8" x 4" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

            Plated Lag Screw
            Bay Standard Mfg

            More Information

            Price: $0.94
            Availability: Stock
            Bay Standard Mfg Item #: LP12100 -

              These 1/2" x 10" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

              All Thread Extension HDG Rods
              Bay Standard Mfg

              More Information

              Price: $2.28
              Availability: Stock
              Bay Standard Mfg Item #: ALL5812HDG -

                These 5/8" x 12" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...

                Hex Head Zinc Plated Machine Bolt
                Bay Standard Mfg

                More Information

                Price: $0.78
                Availability: Stock
                Bay Standard Mfg Item #: MP5845 -

                  These 5/8" x 4-1/2" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                  Plated Lag Screw
                  Bay Standard Mfg

                  More Information

                  Price: $1.20
                  Availability: Stock
                  Bay Standard Mfg Item #: LP12120 -

                    These 1/2" x 12" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                    Square Washer Bearing Plates
                    Quick Build

                    More Information

                    Price: $1.18
                    Availability: Stock
                    Quick Build Item #: BP34-3 -

                      BP34-3 Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates have no corrosion resistance and should not be used with ACQ lumber. Hole Size: 13/16" Dimension: 2-3/4" x 2-3/4" Thickness: 5/16" Coating: None Mild Steel Imported Picture may not match product exactly Brand may be changed at time of shipping ...

                      All Thread Extension Rods
                      Bay Standard Mfg

                      More Information

                      Price: $2.90
                      Availability: Stock
                      Bay Standard Mfg Item #: ALLP5824 -

                        These 5/8" x 24" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request

                        Simpson Strong-Tie Coupling Nut with Witness Hole
                        Simpson Strong-Tie

                        More Information

                        Price: $10.52
                        Availability: Ships Direct
                        Simpson Strong-Tie Item #: CNW7/8-5/8 -

                          Simpson Strong-Tie CNW7/8-5/8 coupling nuts are a tested and load rated method to join 7/8" threaded rod or anchor bolts to 5/8" rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW7/8-5/8 meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW7/8-5/8 Information and Data ...

                          Hot Dipped Galvanized Square Washer Bearing Plates
                          Quick Build

                          More Information

                          Price: $1.74
                          Availability: Stock
                          Quick Build Item #: BP34-3HDG -

                            BP34-3HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 13/16" Dimension: 3" x 3" Thickness: 5/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Brand may be changed at...

                            All Thread Extension Hot Dipped Galvanized Rods
                            Bay Standard Mfg

                            More Information

                            Price: $4.10
                            Availability: Stock
                            Bay Standard Mfg Item #: ALL5824HDG -

                              These 5/8" x 24" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...

                              7/8" - 9 Zinc Plated Hex Nut
                              Bay Standard Mfg

                              More Information

                              Price: $0.34
                              Availability: Stock
                              Bay Standard Mfg Item #: NP78 -

                                7/8" - 9 Zinc Plated Hex Nuts for either 5/8" machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or threaded rod.

                                Simpson Strong-Tie Coupling Nut with Witness Hole
                                Simpson Strong-Tie

                                More Information

                                Price: $15.45
                                Availability: Ships Direct
                                Simpson Strong-Tie Item #: CNW7/8-7/8-OST -

                                  Simpson Strong-Tie CNW7/8-7/8-OST coupling nuts are a tested and load rated method to join 7/8" Hot Dipped Galvanized threaded rod or anchor bolts to 7/8" standard rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW7/8-7/8-OST meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW7/8-7/8-OST Information and Data ...

                                  All Thread Extension Rods
                                  Bay Standard Mfg

                                  More Information

                                  Price: $4.35
                                  Availability: Stock
                                  Bay Standard Mfg Item #: ALLP5836 -

                                    These 5/8" x 36" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request

                                    7/8" - 9 Hot Dipped Galvanized Hex Nut
                                    Bay Standard Mfg

                                    More Information

                                    Price: $0.40
                                    Availability: Stock
                                    Bay Standard Mfg Item #: N78HDG -

                                      7/8" - 9 Hot Dipped Galvanized Hex Nuts for either 7/8" HDG machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or threaded rod. Do not use on plain or zinc plated bolts.

                                      Hex Head Zinc Plated Machine Bolt
                                      Bay Standard Mfg

                                      More Information

                                      Price: $0.85
                                      Availability: Stock
                                      Bay Standard Mfg Item #: MP5850 -

                                        These 5/8" x 5" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                        1" Hex Plated Coupling Nut with Witness Hole
                                        Bay Standard Mfg

                                        More Information

                                        Price: $2.94
                                        Availability: Stock
                                        Bay Standard Mfg Item #: CPNW100 -

                                          1" x 2-11/16" (H) Witness Hole Coupling Nuts are used to connected two 1" threaded rods together or extend a 1" SB and standard anchor bolt. The witness hole allows the inspector to confirm the rods are connected properly. Zinc Plated Hex Head Imported

                                          5/8" x 3" Plated Lag Screw
                                          Bay Standard Mfg

                                          More Information

                                          Price: $0.40
                                          Availability: Stock
                                          Bay Standard Mfg Item #: LP5825 -

                                            These 5/8" x 2-1/2" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                            All Thread Extension Hot Dipped Galvanized Rods
                                            Bay Standard Mfg

                                            More Information

                                            Price: $6.15
                                            Availability: Stock
                                            Bay Standard Mfg Item #: ALL5836HDG -

                                              These 5/8" x 36" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...

                                              Hex Head Zinc Plated Machine Bolt
                                              Bay Standard Mfg

                                              More Information

                                              Price: $1.04
                                              Availability: Stock
                                              Bay Standard Mfg Item #: MP5860 -

                                                These 5/8" x 6" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                1" - 8  Zinc Plated Hex Nut
                                                Bay Standard Mfg

                                                More Information

                                                Price: $0.52
                                                Availability: Stock
                                                Bay Standard Mfg Item #: NP100 -

                                                  1" - 1 Zinc Plated Hex Nuts for either 5/8" machine bolts or all thread rod. Uses 1-1/2" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or threaded rod.

                                                  5/8" x 3" Plated Lag Screw
                                                  Bay Standard Mfg

                                                  More Information

                                                  Price: $0.46
                                                  Availability: Stock
                                                  Bay Standard Mfg Item #: LP5830 -

                                                    These 5/8" x 3" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                    Hex Head Zinc Plated Machine Bolt
                                                    Bay Standard Mfg

                                                    More Information

                                                    Price: $1.16
                                                    Availability: Stock
                                                    Bay Standard Mfg Item #: MP5865 -

                                                      These 5/8" x 6-1/2" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                      5/8" x 4" Plated Lag Screw
                                                      Bay Standard Mfg

                                                      More Information

                                                      Price: $0.76
                                                      Availability: Stock
                                                      Bay Standard Mfg Item #: LP5840 -

                                                        These 5/8" x 4" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                        Hot Dipped Galvanized Square Washer Bearing Plates
                                                        Quick Build

                                                        More Information

                                                        Price: $1.59
                                                        Availability: Stock
                                                        Quick Build Item #: BP78HDG -

                                                          BP78HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 15/16" Dimension: 3" x 3" Thickness: 5/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Brand may be changed at time...

                                                          Hex Head Zinc Plated Machine Bolt
                                                          Bay Standard Mfg

                                                          More Information

                                                          Price: $1.32
                                                          Availability: Stock
                                                          Bay Standard Mfg Item #: MP5870 -

                                                            These 5/8" x 7" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                            Simpson Strong-Tie Coupling Nut with Witness Hole
                                                            Simpson Strong-Tie

                                                            More Information

                                                            Price: $24.98
                                                            Availability: Ships Direct
                                                            Simpson Strong-Tie Item #: CNW1-7/8 -

                                                              Simpson Strong-Tie CNW1-7/8 coupling nuts are a tested and load rated method to join 1" threaded rod or anchor bolts to 7/8" rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW1-7/8 meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW1-7/8 Information and Data ...

                                                              5/8" x 5" Plated Lag Screw
                                                              Bay Standard Mfg

                                                              More Information

                                                              Price: $0.88
                                                              Availability: Stock
                                                              Bay Standard Mfg Item #: LP5850 -

                                                                These 5/8" x 5" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                Hex Head Zinc Plated Machine Bolt
                                                                Bay Standard Mfg

                                                                More Information

                                                                Price: $1.36
                                                                Availability: Stock
                                                                Bay Standard Mfg Item #: MP5880 -

                                                                  These 5/8" x 8" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                  5/8" x 6" Plated Lag Screw
                                                                  Bay Standard Mfg

                                                                  More Information

                                                                  Price: $0.94
                                                                  Availability: Stock
                                                                  Bay Standard Mfg Item #: LP5860 -

                                                                    These 5/8" x 6" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                    Hex Head Zinc Plated Machine Bolt
                                                                    Bay Standard Mfg

                                                                    More Information

                                                                    Price: $1.45
                                                                    Availability: Stock
                                                                    Bay Standard Mfg Item #: MP5890 -

                                                                      These 5/8" x 9" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                      Zinc Plated All Thread Extension Rods
                                                                      Bay Standard Mfg

                                                                      More Information

                                                                      Price: $2.30
                                                                      Availability: Stock
                                                                      Bay Standard Mfg Item #: ALLP3412 -

                                                                        These 3/4" x 12" zinc plated all thread rods when used with a 3/4" coupling nut can be used for extending machine bolts or any other 3/4" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request

                                                                        5/8" x 7" Plated Lag Screw
                                                                        Bay Standard Mfg

                                                                        More Information

                                                                        Price: $1.02
                                                                        Availability: Stock
                                                                        Bay Standard Mfg Item #: LP5870 -

                                                                          These 5/8" x 7" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                          Hex Head Zinc Plated Machine Bolt
                                                                          Bay Standard Mfg

                                                                          More Information

                                                                          Price: $1.66
                                                                          Availability: Stock
                                                                          Bay Standard Mfg Item #: MP58100 -

                                                                            These 5/8" x 10" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                            All Thread Extension Hot Dipped Galvanized Rods
                                                                            Bay Standard Mfg

                                                                            More Information

                                                                            Price: $4.06
                                                                            Availability: Stock
                                                                            Bay Standard Mfg Item #: ALL3412HDG -

                                                                              These 3/4" x 12" hot dipped galvanized all thread rods when used with a 3/4" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...

                                                                              5/8" x 8" Plated Lag Screw
                                                                              Bay Standard Mfg

                                                                              More Information

                                                                              Price: $1.46
                                                                              Availability: Stock
                                                                              Bay Standard Mfg Item #: LP5880 -

                                                                                These 5/8" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                                Hex Head Zinc Plated Machine Bolt
                                                                                Bay Standard Mfg

                                                                                More Information

                                                                                Price: $1.69
                                                                                Availability: Stock
                                                                                Bay Standard Mfg Item #: MP58110 -

                                                                                  These 5/8" x 11" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                                  Hot Dipped Galvanized Square Washer Bearing Plates
                                                                                  Quick Build

                                                                                  More Information

                                                                                  Price: $2.52
                                                                                  Availability: Stock
                                                                                  Quick Build Item #: BP100HDG -

                                                                                    BP100HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 1-1/16" Dimension: 3-1/2" x 3-1/2" Thickness: 3/8" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Brand may be...

                                                                                    Zinc Plated All Thread Extension Rods
                                                                                    Bay Standard Mfg

                                                                                    More Information

                                                                                    Price: $4.10
                                                                                    Availability: Stock
                                                                                    Bay Standard Mfg Item #: ALLP3424 -

                                                                                      These 3/4" x 24" zinc plated all thread rods when used with a 3/4" coupling nut can be used for extending machine bolts or any other 3/4" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request

                                                                                      5/8" x 9" Plated Lag Screw
                                                                                      Bay Standard Mfg

                                                                                      More Information

                                                                                      Price: $2.18
                                                                                      Availability: Stock
                                                                                      Bay Standard Mfg Item #: LP5890 -

                                                                                        These 5/8" x 9" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                                        Hex Head Zinc Plated Machine Bolt
                                                                                        Bay Standard Mfg

                                                                                        More Information

                                                                                        Price: $2.28
                                                                                        Availability: Stock
                                                                                        Bay Standard Mfg Item #: MP58120 -

                                                                                          These 5/8" x 12" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                                          All Thread Extension Hot Dipped Galvanized Rods
                                                                                          Bay Standard Mfg

                                                                                          More Information

                                                                                          Price: $7.25
                                                                                          Availability: Stock
                                                                                          Bay Standard Mfg Item #: ALL3424HDG -

                                                                                            These 3/4" x 24" hot dipped galvanized all thread rods when used with a 3/4" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...

                                                                                            5/8" x 10" Plated Lag Screw
                                                                                            Bay Standard Mfg

                                                                                            More Information

                                                                                            Price: $1.54
                                                                                            Availability: Stock
                                                                                            Bay Standard Mfg Item #: LP58100 -

                                                                                              These 5/8" x 10" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture

                                                                                              Hex Head Zinc Plated Machine Bolt
                                                                                              Bay Standard Mfg

                                                                                              More Information

                                                                                              Price: $2.18
                                                                                              Availability: Stock
                                                                                              Bay Standard Mfg Item #: MP58140 -

                                                                                                These 5/8" x 14" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture

                                                                                                Zinc Plated All Thread Extension Rods
                                                                                                Bay Standard Mfg

                                                                                                More Information

                                                                                                Price: $6.15
                                                                                                Availability: Stock
                                                                                                Bay Standard Mfg Item #: ALLP3436 -

                                                                                                  These 3/4" x 36" zinc plated all thread rods when used with a 3/4" coupling nut can be used for extending machine bolts or any other 3/4" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request