Login/Register
Shopping Cart
OR
Filter
Sort By
The THD37400HMG Mechanical Galvanized 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD...
The THD37400HMG Mechanical Galvanized 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced...
The Simpson Strong-Tie TNT25214TF Titen Turbo™ 1/4" x 2-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...
The Simpson Strong-Tie TNT25214TF Titen Turbo™ 1/4" x 2-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...
1" x 2-11/16" (H) Witness Hole Coupling Nuts are used to connected two 1" threaded rods together or extend a 1" SB and standard anchor bolt. The witness hole allows the inspector to confirm the rods...
1" x 2-11/16" (H) Witness Hole Coupling Nuts are used to connected two 1" threaded rods together or extend a 1" SB and standard anchor bolt. The witness hole allows the inspector to confirm the rods are connected properly. Zinc Plated Hex Head Imported Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in...
BP34-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot...
BP34-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 13/16" Dimension: 2" x 2" Thickness: 3/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Hot Dipped Galvanized...
These 5/8" x 2-1/2" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 5/8" x 2-1/2" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance...
These 5/8" x 6" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length...
These 5/8" x 6" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of...
GRK's 5" x #9 Trim Head Finish screws are an excellent choice for most fine carpentry applications, as well as window extension jambs and more. The small head shape easily countersinks leaving...
GRK's 5" x #9 Trim Head Finish screws are an excellent choice for most fine carpentry applications, as well as window extension jambs and more. The small head shape easily countersinks leaving a small hole to fill. The small head and W-Cut™ thread design limits splitting problems in your finished product. #9 size provides additional holding strength. Recessed Star Drive: Zero Stripping, with 6 points of contactTrim head: for a clean finished lookW-Cut™: Low torque,...
Head is Painted Tan! The Simpson S11A237KJT 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when...
Head is Painted Tan! The Simpson S11A237KJT 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when applicable. The countersunk casing head with a checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank 21º...
The Simpson S15N200SFB 2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style...
The Simpson S15N200SFB 2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1 Hitachi: NT64MA4...
Simpson Strong-Tie PDPAWL-287 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin...
Simpson Strong-Tie PDPAWL-287 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin preassembled with a 1″ washer that provides additional bearing surface for enhanced upload resistance. Length: 2-7/8" Head Diameter: .300" Shank Diameter: .157" Coating: Standard G90 Zinc PDPAWL Series Fasteners Tension and Shear Loads in Normal Weight Concrete PAT Fastener MSDS Standard G90 Zinc...
The Simpson Strong-Drive® SDS25312 1/4" x 3-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25312 screw...
The Simpson Strong-Drive® SDS25312 1/4" x 3-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25312 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 3-1/2" Thread Length: 2-1/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive...
The Simpson Strong-Tie THD37300CS6SS 3/8" x 3" TITEN HD Type 316 Stainless Countersunk Screw Anchor with countersunk head is part of a family of products that sets the standard for high-performance...
The Simpson Strong-Tie THD37300CS6SS 3/8" x 3" TITEN HD Type 316 Stainless Countersunk Screw Anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of installation. Designed for use in dry, interior, noncorrosive environments or temporary outdoor applications, the countersunk Titen HD offers industry-leading performance even in seismic conditions. The countersunk head style is for applications that require a flush-mount...
The THD37500H 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...
The THD37500H 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...
The Simpson Strong-Tie THD37600H6SS Type 316 Stainless Steel 3/8" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD37600H6SS Type 316 Stainless Steel 3/8" x 6" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie TNT18234H Titen Turbo™ 3/16" x 2-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of...
The Simpson Strong-Tie TNT18234H Titen Turbo™ 3/16" x 2-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping and...
The Intercorp Strong-Point 2-1/2" x #8 Yellow Zinc Coarse Phillips Bugle Drywall Screws are a specialized type of fastener designed for attaching drywall (also known as gypsum board or sheetrock) to...
The Intercorp Strong-Point 2-1/2" x #8 Yellow Zinc Coarse Phillips Bugle Drywall Screws are a specialized type of fastener designed for attaching drywall (also known as gypsum board or sheetrock) to wood or steel framing during both residential and commercial construction. Drywall fasteners can also used for other applications, such as attaching drywall to furring strips and installing drywall to existing walls and ceilings during renovations. These drywall fasteners offer several design...