Products 1-24 of 27
Show
Availability: Stock
Simpson Strong-Tie
Item #: H1 -
The Simpson Strong-Tie H1 Hurricane and Seismic Ties are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H1Z -
The Simpson Strong-Tie H1Z Hurricane Ties with ZMax® Corrosion Resistance are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1Z Information and Installation Instructions. ZMax® Galvanized Coating Information...
Availability: Stock
Simpson Strong-Tie
Item #: H1.81Z -
The Simpson Stron-Tie H1.81Z ZMax® Hurricane Tie is designed for use with 1 3/4" LVL roof rafters to provide a stronger connection to the top plate of the wall. It's ideal for connections when there are higher-load demands on the structure, like a heavy snow load, and provides lateral resistance in a seismic event. This 1 3/4"-wide H1.81Z connector is the first hurricane tie to be specifically sized for engineered wood. The H1.81Z installs with half the nails that are needed for two...
Availability: Stock
Simpson Strong-Tie
Item #: H2.5A -
The Simpson Strong-Tie H2.5A Ties can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (10) 8d x 1-1/2" Nails or (10) SD9 x 1-1/2" Screws H2.5A Information and Installation Instructions. Standard G90 Zinc Galvanized...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H2.5AZ -
The Simpson Strong-Tie H2.5AZ Ties with ZMax® Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5A Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. You can also substitute the Simpson SD #9 x 1-1/2" Structural Screw. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H2.5AZ Information and Installation...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H2.5ASS -
The Simpson Strong-Tie H2.5ASS Ties with 316L Stainless Steel Corrosion Protection can be used as either left or right side ties in the middle of the run. The H2.5ASS Hurricane Ties connects the double top plate to the rafter or truss. This clip accepts 8d .131" x 1-1/2" joist nails or longer. Material: 18 Gauge Finish: Type 316L Stainless Steel Fasteners: (10) 8d x 1-1/2" Nails H2.5ASS Information and Installation Instructions. Type 316L Connector Stainless Steel Information Type 316L...
Availability: Stock
Simpson Strong-Tie
Item #: H2A -
The Simpson Strong-Tie H2A Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2A installation ties the rafter to the stud while spanning a top plate. The Simpson H2A requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (12) 8d x 1-1/2" Nails H2A Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H2AZ -
The Simpson Strong-Tie H2AZ ZMax® Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2AZ installation ties the rafter to the stud while spanning a top plate. The Simpson H2AZ requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (12) 8d x 1-1/2" Nails H2AZ Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating...
Availability: Stock
Simpson Strong-Tie
Item #: H3 -
The Simpson Strong-Tie H3 Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3 installation ties the single top plate to the rafter or truss. The Simpson H3 requires (8) 8d joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (8) 8d x 2-1/2" Nails H3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H3Z -
The Simpson Strong-Tie H3Z Clip with ZMax® Corrosion resistance is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H3Z installation ties the single top plate to the rafter or truss. The Simpson H3Z requires (8) 8d joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (8) 8d x 2-1/2" Nails H3Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax®...
Availability: Stock
Simpson Strong-Tie
Item #: H6 -
Simpson Strong-Tie H6 Hurricane Tie are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6 Tie requires (16) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: Standard G90 Zinc Fastener Options: (16) 8d x 1-1/2" Nails H6 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H6Z -
Simpson Strong-Tie H6Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6Z Tie requires (16) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (16) 8d x 1-1/2" Nails H6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a...
Availability: Stock
Simpson Strong-Tie
Item #: H7Z -
Simpson Strong-Tie H7Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to both the top plate and rafter. The H7Z Tie requires (14) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (14) 8d x 1-1/2" Nails H7Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating)...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H8 -
Simpson Strong-Tie H8 Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8 Hurricane Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: Standard G90 Zinc Coating Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
Availability: Stock
Simpson Strong-Tie
Item #: H8Z -
Simpson Strong-Tie H8Z ZMax® Hurricane Tie for attaching double top plates to a rafter, stud to a sill plate or I-joist to double top plates. The H8Z Tie uses (10) 10d .148" x 1-1/2" joist nails or SD #9 x 1-1/2" Structural Screws. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (10) 8d x 1-1/2" Nails (10) SD9 x 1-1/2" Screws H8Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per...
Availability: Stock
Simpson Strong-Tie
Item #: H10A -
Simpson Strong-Tie H10A Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10A can also be field-bent to connect to shear blocking as well. The H10A uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10A Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H10AZ -
Simpson Strong-Tie H10AZ with ZMax® Corrosion Protection Hurricane Tie for connection a double top plate to a 2x rafter or truss. The H10AZ can also be field-bent to connect to shear blocking as well. The H10AZ uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (18) 10d .148" x 1-1/2" H10A Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H10AR -
Simpson Strong-Tie H10AR Hurricane Tie for connection a double top plate to a 2x rough sawn rafter or truss. The H10AR can also be field-bent to connect to shear blocking as well. The H10AR uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10AR Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H10S -
Simpson Strong-Tie H10S Hurricane Tie for connecting the stud to both the top plates and 2x rafter. The connection to the stud may be center or offset (load value reduces when offset). The H10S Tie uses (24) 8d .131" x 1-1/2" or longer joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (24) 8d x 1-1/2" Nails H10S Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per...
Availability: Stock
Simpson Strong-Tie
Item #: H10A-2 -
Simpson Strong-Tie H10A-2 Hurricane Tie for connection a double top plate to double 2x rafters or trusses. The H10A-2 uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (18) 10d .148" x 1-1/2" H10A-2 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H10A-2Z -
Simpson Strong-Tie H10A-2Z ZMax® Hurricane Tie for connection a double top plate to double 2x rafters or trusses. The H10A-2Z ZMax® uses (18) 10d .148" x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (18) 10d .148" x 1-1/2" H10A-2Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating) than the standard hot-dip galvanized coating...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H11Z -
Simpson Strong-Tie H11Z Hurricane Tie with ZMax® Corrosion Protection for creating a seismic connection between a double top plate and a 3x rafter or truss. Material: 18 Gauge Finish: ZMax® G-185 Coating Fastener Options: (12) 16d" x 2-1/2" H11Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185 coating) than the standard hot-dip galvanized coating (galvanized per ASTM A653...
Availability: Stock
Simpson Strong-Tie
Item #: H14 -
Simpson Strong-Tie H14 Hurricane Ties create a connection between either double top plates or double 2x header to a 2x rafter or truss. The bottom flange wrap the top plate but can be straightened to face nail to a header. Material: 18 Gauge Finish: Standard G90 Zinc Fastener Options: (12) 8d x 1-1/2" Nails (Rafter/Truss) (13) or (15) 8d (Plates) H14 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90...
Availability: Ships Direct
Simpson Strong-Tie
Item #: H16 -
The H16 Hurricane-Tie has a pre-sloped seat of 5/12 for double trusses. The pre-sloped seat of the H16 series ties provides for a tight fit and reduced deflection. The strap length provides for various truss height up to a maximum of 13 1/2" (H16 series). Minimum heel height for H16 series is 4". Truss rafter pitch of 3/12 to 7/12 is acceptable. Shorter strap allows for less wrapping of straps when applicable. Material: 18 Gauge Width: 1-5/8" Height: 18-3/4" Finish: Standard G90 Zinc...