Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson Strong-Tie PAB5-18 5/8" x 18" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB5-18 5/8" x 18" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
Save by Purchasing a Quantity of 400 SSTB20L Bolts! The Simpson Strong-Tie SSTB20L (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall...
Save by Purchasing a Quantity of 400 SSTB20L Bolts! The Simpson Strong-Tie SSTB20L (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 24-5/8" Minimum...
The Simpson Strong-Tie MASB is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced...
The Simpson Strong-Tie MASB is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced anchor bolts. The MASB easily installs into wet concrete-grouted CMU block for a time-saving alternative to anchor bolts. Offset design for use in concrete block applications One-piece design, so there are no nuts and washers to lose Unique design eliminates concerns about stud placement 16 gauge...
The Simpson Strong-Tie PAB5-18 5/8" x 18" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and...
The Simpson Strong-Tie PAB5-18 5/8" x 18" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from high strength steel for higher load values. Please call our sales department direct at 800-323-2999 for pricing and...
The Simpson Strong-Tie SSTB20LHDG Hot Dipped Galvanized (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...
The Simpson Strong-Tie SSTB20LHDG Hot Dipped Galvanized (5/8" Diameter by 24-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 24-5/8" Minimum Embedment: 16-5/8" Finish: Hot...
The Simpson Strong-Tie MASBZ ZMax® is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with...
The Simpson Strong-Tie MASBZ ZMax® is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced anchor bolts. The MASB easily installs into wet concrete-grouted CMU block for a time-saving alternative to anchor bolts. Offset design for use in concrete block applications One-piece design, so there are no nuts and washers to lose Unique design eliminates concerns about stud placement 16...
The Simpson Strong-Tie LMA4Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x4 or 3x4 mudsills. The unique design provides installation...
The Simpson Strong-Tie LMA4Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x4 or 3x4 mudsills. The unique design provides installation flexibility, eliminating problems associated with wall framing alignment interfering with foundation anchors. The LMA4Z has a ZMax® coating, a thicker galvanized finish that helps extend the service life of the connector. Suitable for stem wall or slab foundations One-piece design, so there are no nuts...
The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum Embedment: 20-5/8" Finish: None Rolled threads for higher...
The Simpson Strong-Tie LMA6Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x6 or 3x6 mudsills. The unique design provides installation...
The Simpson Strong-Tie LMA6Z is a mudsill anchor that provides an economical replacement for 1/2" sill plate anchor bolts in a 2x6 or 3x6 mudsills. The unique design provides installation flexibility, eliminating problems associated with wall framing alignment interfering with foundation anchors. The LMA6Z has a ZMax® coating, a thicker galvanized finish that helps extend the service life of the connector. Suitable for stem wall or slab foundations One-piece design, so there are no nuts...
The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB5-18-HDG 5/8" x 18" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
Save by Purchasing a Quantity of 500 SSTB24 Bolts! The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall...
Save by Purchasing a Quantity of 500 SSTB24 Bolts! The Simpson Strong-Tie SSTB24 (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum...
The Simpson Strong-Tie PAB5-24 5/8" x 24" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...
The Simpson Strong-Tie PAB5-24 5/8" x 24" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...
The Simpson Strong-Tie SSTB24HDG Hot Dipped Galvanized (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...
The Simpson Strong-Tie SSTB24HDG Hot Dipped Galvanized (5/8" Diameter by 25-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 25-5/8" Minimum Embedment: 20-5/8" Finish: Hot...
The Simpson Strong-Tie MAB15 mudsill anchor features design flexibility to anchor the mudsill to concrete block, poured walls or slab foundations. Because of its unique design, the MAB15 can...
The Simpson Strong-Tie MAB15 mudsill anchor features design flexibility to anchor the mudsill to concrete block, poured walls or slab foundations. Because of its unique design, the MAB15 can eliminate certain problems associated with misplaced anchor bolts. The MAB15 can be installed for 2x4,6,8,10 or 12 mudsills. Suitable for stem wall, concrete block or slab foundations One-piece design, so there are no nuts and washers to lose A easily installed alternative to standard anchor bolts 18 gauge...
The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...
The Simpson Strong-Tie PAB5-24-HDG 5/8" x 24" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...
The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...
The Simpson Strong-Tie SSTB24L (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 28-1/8" Minimum Embedment: 20-5/8" Finish: None Rolled threads for higher...