Products 1-7 of 7
Show
Availability: Stock
Simpson Strong-Tie
Item #: GBC -
Simpson Strong-Tie GBC Gable Brace Connector provides improved anchorage of gable bracing to the exterior wall. Installation flexibility for brace angle. GBC has tension and compression capacities. GBC clips must be installed in pairs to reach full load capacity. Material: 16 Gauge Finish: Standard G90 Zinc Installation Angles: 40° to 60° Fasteners-Gable Brace: (5) 8d x 1-1/2" Nails Fasteners-Top Plates: (7) 8d Nails GBC Information and Installation Instructions. Standard G90 Zinc...
Availability: Stock
Simpson Strong-Tie
Item #: RBC -
The Simpson Strong-Tie RBC roof boundary clip is designed to aid installation and transfer shear loads between the roof diaphragm and wall. The locator tabs make proper location of the clip easy. The RBC can be used on wood or masonry walls and will handle roof pitches from 0/12 to 12/12. The RBC is available as a special order with prongs into one side (RBCP) for pre-attachment of the part to a block at the truss plant. Material: 20 Gauge Finish: Standard G90 Zinc Fasteners-to-blocking: (6)...
Availability: Ships Direct
Simpson Strong-Tie
Item #: TBE4 -
The Simpson Strong-Tie TBE4 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 4 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It replaces nail-on scabs that provide lower load transfer, or in some cases, an additional ply when needed for bearing. One size works with any number of girder plies. Must be used in pairs Material: 18 Gauge Finish: Standard G90 Zinc Width: 3-9/16" Fasteners (Rafter): (10) .148 x 1-1/2" Nails (Single Truss...
Availability: Ships Direct
Simpson Strong-Tie
Item #: TBE6 -
The Simpson Strong-Tie TBE6 Truss Bearing Enhancer transfers load from the truss or girder to 2 x 6 wall top plates for bearing-limited conditions and provides exceptional uplift capacity. It replaces nail-on scabs that provide lower load transfer, or in some cases, an additional ply when needed for bearing. One size works with any number of girder plies. Must be used in pairs Material: 18 Gauge Finish: Standard G90 Zinc Width: 5-9/16" Fasteners (Rafter): (10) .148 x 1-1/2" Nails (Single Truss...
Availability: Ships Direct
Simpson Strong-Tie
Item #: TJC37 -
The Simpson Strong-Tie TJC37 is a versatile connector for jack trusses. Adjustable from 0° to 85°, you can bend the TJC to the desired position (one bend cycle only). Each TJC is shipped with 67.5° bend. Nail hole locations allow for easy installation. No bevel cut is required. Minimum nailing option on TJC37 provides faster installation and lower installed cost. Material: 16 Gauge Finish: Standard G90 Zinc Width: 3-1/8" x 3-1/2" x 3-1/2" Fasteners (Minimum): (4) .131 x 1-1/2"...
Availability: Ships Direct
Simpson Strong-Tie
Item #: TJC57 -
The Simpson Strong-Tie TJC57 is a versatile connector for jack trusses. Adjustable from 0° to 85°, you can bend the TJC to the desired position (one bend cycle only). Each TJC is shipped with 67.5° bend. Nail hole locations allow for easy installation. No bevel cut is required. SD screws can be used to increase standard load values. Material: 16 Gauge Finish: Standard G90 Zinc Width: 5-1/8" x 3-1/2" x 3-1/2" Fasteners (Nails): (12) .131 x 1-1/2" Nails (Carrying Member) (12) .131 x...
Availability: Ships Direct
Simpson Strong-Tie
Item #: TSP -
Simpson Strong-Tie TSP Stud Plate for connecting the top plate to either the wall stud or 2x rafter. The TSP Tie uses (9) 10d .131" x 1-1/2" to the stud or rafter and (6) 10d x 1-1/2" or 3" to the top plate depending on the load value required. Material: 16 Gauge Finish: Standard G90 Zinc Fastener Options: (9) 10d x 1-1/2" Nails (Stud or Rafter) (6) 10d x 1-1/2" or 3" (Top Plate) TSP Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc...