Login/Register
Shopping Cart
OR
Save by Purchasing a Pallet of 72 Boxes The Simpson Strong-Tie A34 Framing Clips for wood to wood connections at a 90° angle. Material: 18 Gauge Finish: Standard G90 Galvanized Length: 2-1/2" Flange Widths: 1-7/16" Fasteners: (8) 8d x 1-1/2" (8) SD #9 x 1-1/2" A34 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a...
The Metabo-HPT Power Tool's 8 Amp VB16Y Rebar Bender and Cutter allows you to field cut and bend 3/8", 1/2" and 5/8" grade 60 rebar up to 180°'s. Weighing only 39.7 lbs. makes it easy to set up and move around the jobsite reducing time to get the job competed. Includes: Deflection Guard (320914), Cutter Set (1 pair) (319706) and D62 Center Roller (319714) 8 Amp motor, iintense power (530W) that it uniformly bends up to No.5 (3/8", 1/2", 5/8") Grade 60 rebar at a maximum angle of 180...
Save by Purchasing a Quantity of 24 Boxes (1200 Pieces)! Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS26 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized...
Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-6 Information and Installation Instructions. Gray Paint Coating Information...
Cuts Wood Up To 12 Inches Thick The Everett Portable Bandsaw (Formerly Oliver Machine Products) Model EPB12MPLUS 12" Portable Band Saw is the finest tool of its kind on the market. This tool was originally designed and built in 1973 primarily for the use in cutting of band saw materials, such as: corbels, outlookers, rounded rafter tails, band-sawed beams, scalloped materials and much more. All your special cutting that in the past had to be cut in yards. Now you can create these special cuts...
Save by Purchasing a Quantity of 48 Boxes (4800 Pieces)! Simpson Strong Tie LUS24 2 x 4 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS24 hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16"...
Save by Purchasing a Quantity of 12 Boxes (240 Pieces)! Simpson Strong-Tie HDU2-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (6) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 14 Gauge Steel Finish: Standard...
Save by Purchasing a Quantity of 36 Boxes (360 Pieces)! The Simpson PB44 Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Common Nails PB44 information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of...
Save by Purchasing a Pallet of 44 Boxes! Simpson Strong-Tie MASA anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASA is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASA version is used for installation on standards forms. Attaches easily to the concrete form for quick installation Lays flat on the form board so there is no anchor bolt to finish around No...
Save by Purchasing a Quantity of 10 Boxes (100 Bases)! Simpson Strong-Tie CB44 column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 2" Wide Galvanized Steel Base Material: 7 Ga Galvanized (3-9/16" x 3-9/16") Fasteners: (2) 5/8" Machine Bolts CB44 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
Save by Purchasing a Quantity of 6 Boxes (72 Pieces)! The Simpson CBSQ44-SDS2 (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 4 x 4 Nominal (3-1/2" x 3-1/2") Base: 12 Ga. (3-9/16" x 3-1/2") Strap: 10 Ga. x 2-1/4"...
Save by Purchasing a Quantity of 500 SSTB16 Bolts! The Simpson Strong-Tie SSTB16 (5/8" Diameter by 17-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 17-5/8" Minimum...