OCM, Inc Concrete Accessories

OCM., Inc. is a Subsidiary of OKABE Co., Ltd.. OKABE was founded in 1917 in Japan and has been a full service manufacturer and distributor of concrete construction supplies, and a world leader in the Metal Forming Industry for ninety years. OKABE uses a broad range of metal forming technologies to provide a diverse selection of engineered fasteners and components for builders worldwide. DHC Supplies many of the OCM concrete forming supplies required to build footings, stem wall and retaining walls. We invite you to visit the
OCM website to see their full line of accessories. If there is anything on the site that we do not stock we will gladly create a special order for direct shipment if possible. Just call our sales department at 800-323-2999 for more information.
Products 1-24 of 35
Show
Availability: Stock
Item #: REBARCAP -
OCM #3 - #8 Mushroom Rebar Protection Caps provide scratch protection when working around in-place rebar. They only help protect workers against minor injuries caused by exposed rebar or pipes. Very Important: These caps do not provide impalement protection. You must use OSHA Rebar Safety Caps to meet impalement protection requirements. Please check you local codes for further information.
Availability: Stock
Item #: STSEC-6HH -
OCM, Inc #STSEC-6HH 6" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
Item #: SC06-75 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 6" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
Item #: CHAIR2 -
OCM 2" or 2-1/4" PCC2.00-2.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 3-1/2" base diameter Fits up to #8 rebar Will not puncture...
Availability: Ships Direct
Item #: SC0762-118 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 7-5/8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
Item #: JAHN-A -
OCM ACLMP Jahn-A Bracket is fabricated from high strength steel with a cad plated eccentric and painted body. The 5/8" take-up of the eccentric compensates for minor lumber variations in thickness. This Jahn-A Bracket can be utilized to hold a single horizontal wale or a single vertical stud with any type of wall form; round, curved, battered, beam and/or columns. The Jahn-A Bracket can be installed before or after the wales have been positioned. The slots in the bracket allow it to slip over...
Availability: Stock
Item #: STLEC-6HH -
OCM, Inc #STLEC-6HH 6" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties use...
Availability: Stock
Item #: SC08-75 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 8" wide wall using 3/4" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
Item #: STSEC-8HH -
OCM, Inc #STSEC-8HH 8" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
Item #: CHAIR3 -
OCM 3" or 3-1/4" PCC3.00-3.25 Plastic Rebar Support Chairs are lightweight, yet strong enough to hold up to 600 lbs. Each chair has two height settings for more versatility during installation. Applications include slab on grade, insulated sandwich panels, vapor barrier, poorly compacted or loose soils. Also, these chairs can support mesh or rebar, and meets current CRSI requirments. Accommodates rebar sizes to 1" in diameter 4-1/8" base diameter Fits up to #8 rebar Will not puncture...
Availability: Stock
Item #: STWEGP -
OCM STWEGP Snap-Tie Wedges (also known as hairpin wedges) can either be used in a double waler forming system or applies directly to the plywood when using stubby snap ties. The OCM STWEGP Snap-Tie Wedges is a high strength snap tie wedge with a safe working load of 3,325 lbs. It is designed to slip over the head of standard or heavy duty snap ties to provide ample bearing area for proper load distribution into the wales. The wedge can also be applies directly to the plywood when using stubby...
Availability: Stock
Item #: STLEC-8HH -
OCM, Inc #STLEC-8HH 8" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties use...
Ship Free!
Availability: Stock
Item #: STWEGP-100 -
OCM STWEGP Snap-Tie Wedges (also known as hairpin wedges) can either be used in a double waler forming system or applies directly to the plywood when using stubby snap ties. The OCM STWEGP Snap-Tie Wedges is a high strength snap tie wedge with a safe working load of 3,325 lbs. It is designed to slip over the head of standard or heavy duty snap ties to provide ample bearing area for proper load distribution into the wales. The wedge can also be applies directly to the plywood when using stubby...
Availability: Stock
Item #: SC08-118 -
The OCM, Inc Walerless Plywood Spreader Cleat Form System is used when forming a 8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc Spreader Cleat System is excellent for low wall...
Availability: Stock
Item #: STSEC-10HH -
OCM, Inc #STSEC-10HH 10" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
Item #: TURNBUCKLE -
OCM TBFB-BF Turnbuckle Form Aligner with Bent Plate are designed to accurately position and plumb vertical forms and framed walls. The turnbuckle section of the aligner features a 1" diameter self-cleaning coil thread for fast adjustments. Overall length of the aligner is 35" minimum and 39" maximum, offering 4" of effective adjustment. The OCM TBFB-BF Turnbuckle Form Aligner has a bent nailing plate equipped with nail holes for nailing to forms and a 15/16" hole to accept 3/4" or 7/8" round...
Availability: Stock
Item #: STLEC-10HH -
OCM, Inc #STLEC-10HH 10" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties...
Availability: Stock
Item #: HOOK24 -
OCM Screed Brackets clamp to the top of a nail stake and hold screed bar parallel to the form during flat work finishing. Screed brackets are available for 1/2" x 2" flat bar and 2x4's. OCM Screed Brackets are used with 3/4" round nail stakes.
Availability: Stock
Item #: STSEC-12HH -
OCM, Inc #STSEC-12HH 12" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Stock
Item #: STLEC-12HH -
OCM, Inc #STLEC-12HH 12" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties...
Availability: Ships Direct
Item #: STSEC-14HH -
OCM, Inc #STSEC-14HH 14" Wall x 4-3/4" End Hex Head Plastic Cone Snap Ties can be used with either the #1 or #2 forming systems with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge or Jahn Bracket. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The...
Availability: Ships Direct
Item #: STLEC-14HH -
OCM, Inc #STLEC-14HH 14" Wall x 8-1/4" End Hex Head Plastic Cone Snap Ties can be used with the #3 forming system with 3/4" plywood. This snap tie forming method is used for retaining and standard walls, batter walls, bridges, concrete signs, footings, etc. They are held in place by a Snaptie Wedge. OCM, Inc Hex Head Snap Ties are manufactured with integral heads. The hex head allows short-end snap ties to be broken back with the form work still in place. The standard OCM hex head snap ties...
Availability: Ships Direct
Item #: SC10-118 -
The OCM, Inc SC10-118 Walerless Plywood Spreader Cleat Form System is used when forming a 10" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc SC10-118 Spreader Cleat System is...
Availability: Ships Direct
Item #: SC1162-118 -
The OCM, Inc SC1162-118 Walerless Plywood Spreader Cleat Form System is used when forming a 11-5/8" wide wall using 1-1/8" plywood. The OCM, Inc Spreader Cleats are designed for the contractor who is engaged in a variety of form work up to 32" high. On panels up to 24" high the cleats are spaced at 32" maximum center to center spacing. For panels over 24" and up to 32" high, the spreader cleats should be spaced a maximum of 24" center to center. The OCM, Inc SC1162-118 Spreader Cleat System is...