Simpson Strong-Tie

The Simpson Strong-Tie DSVT212R5LB #10 x 2-1/2" Deck Drive™ Tan Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...

The Simpson Strong-Tie DSVT212R5LB #10 x 2-1/2" Deck Drive™ Tan Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSV is ideally suited to be driven and countersunk into today’s wood deck boards. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber. Also DSV screws are available in collated strips for use in the Quik Drive® auto-feed screw driving...

The Simpson Strong-Tie 1-3/4" x 9-1/2" MIT9.5 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...

The Simpson Strong-Tie 1-3/4" x 9-1/2" MIT9.5 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...

The 1-1/4" wide x 12" long LTS12 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist...

The 1-1/4" wide x 12" long LTS12 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 12" (Length) Fasteners: 10d or 10d x 1-1/2" depending on load value required and depth of receiving member (See...

Simpson Strong-Tie Outdoor Accents® APA21 angles tie together beams, rafters and more. The APA21 angle makes structural connections between beams and posts much more visually appealing. These...

Simpson Strong-Tie Outdoor Accents® APA21 angles tie together beams, rafters and more. The APA21 angle makes structural connections between beams and posts much more visually appealing. These angles make connections stronger and provide consistent, straight corners for a variety of outdoor projects. Install with Outdoor Accents® structural screws and hex-head washer (sold separately) for a decorative look. Stronger than angled nailing or screw fastening alone for outdoor living or home...

The 1-1/4" wide x 12" long LTS12SS Stainless Steel Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss...

The 1-1/4" wide x 12" long LTS12SS Stainless Steel Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. LTS12SS straps should be used where severe corrosive conditions exist. Material: 18 gauge Finish: Stainless Steel Dimensions: 1-1/4" (Wide) x 12" (Length) Fasteners: 10d or...

The Simpson Strong-Tie 1-3/4" x 11-7/8" MIT11.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but...

The Simpson Strong-Tie 1-3/4" x 11-7/8" MIT11.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...

The Simpson Strong-Tie DSVR212R5LB #10 x 2-1/2" Deck Drive™ Red Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...

The Simpson Strong-Tie DSVR212R5LB #10 x 2-1/2" Deck Drive™ Red Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSV is ideally suited to be driven and countersunk into today’s wood deck boards. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber. Also DSV screws are available in collated strips for use in the Quik Drive® auto-feed screw driving...

The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie...

The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie addresses a 2015 International Residential Code provision (section R507.2.4) that now allows four 750 lb. lateral connectors to be fastened to framing in the house with a lag screw. This provision is an alternative to using two 1,500 lb. lateral connections from the deck to the floor joists within the...

Simpson Strong Tie HUCQ1.81/11-SDS 1-3/4" Wide x 11" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/11-SDS hangers with...

Simpson Strong Tie HUCQ1.81/11-SDS 1-3/4" Wide x 11" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/11-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-3/4" (Wide) x 11" (Height) x 3" (Seat Depth) Included Fasteners: (10) SDS 1/4" x 1-3/4" Screws (Header) (4) SDS 1/4" x 1-3/4"...

The Simpson Strong-Tie CBT4Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether...

The Simpson Strong-Tie CBT4Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether you’re designing for a custom indoor or outdoor living space, the tubular shape of the CBTZ allows an easy-to-install beam-to-post connection using common tools. The CBT4Z is designed to connect beams and posts of a variety of sizes. The CBT4Z accommodates a minimum 6x6 post and 6x8 beam using six...

The Simpson Strong-Tie CPT66Z concealed 6 x 6 post base provides a clean, concealed look while providing a 1" standoff height above concrete. The 1" standoff reduces the potential for decay at the...

The Simpson Strong-Tie CPT66Z concealed 6 x 6 post base provides a clean, concealed look while providing a 1" standoff height above concrete. The 1" standoff reduces the potential for decay at the post end and satisfies code requirements for posts that are exposed to weather, water splash or in basements. Each base includes (3) 1/2" x 4-3/4" mechanical galvanized dowels. If 1/2" machine bolts are substituted it is recommended they are hot dipped galvanized. The CPT66Z is tested and load-rated...

The Simpson Strong-Tie EDTA22P Pneumatic tool features an optional suitcase handle adapter for the ultimate in tool configuration and dispensing convenience. The suitcase option enables easier and...

The Simpson Strong-Tie EDTA22P Pneumatic tool features an optional suitcase handle adapter for the ultimate in tool configuration and dispensing convenience. The suitcase option enables easier and time-saving ground-level doweling. The heavy duty EDTA22P tool comes with a custom, blow-molded plastic carrying case. This tool uses SET22-N and SETXP22-N adhesives. Explanation of "Simpson Ships Direct" Availability Direct Shipments from Simpson Strong-Tie are products Simpson stocks in many of...

The Simpson Strong-Tie PC4Z Post Cap is designed with the post and beam flanges in-line so that the PC4Z center post cap can accommodate several 4x post sizes as well as double 2x4 studs. The PC4Z...

The Simpson Strong-Tie PC4Z Post Cap is designed with the post and beam flanges in-line so that the PC4Z center post cap can accommodate several 4x post sizes as well as double 2x4 studs. The PC4Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Please Note: This cap may be special ordered in a rough...

The Simpson AC4Z ZMax® Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. ZMax® protection provides additional corrosion resistance when applicable....

The Simpson AC4Z ZMax® Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. ZMax® protection provides additional corrosion resistance when applicable. Material: 18 Gauge Finish: ZMax® G-185 Galvanized Dimensions 3-9/16" (W) x 6-1/2" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162 x 3-1/2" Nails (Max) Post and Beam...(28) SD10 x 1-1/2" (Max) AC4Z...

The Simpson Strong-Tie ABW44RZ for rough 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above...

The Simpson Strong-Tie ABW44RZ for rough 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW44RZ...

Simpson Strong-Tie HD3BHDG Hot Dipped Galvanized Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other...

Simpson Strong-Tie HD3BHDG Hot Dipped Galvanized Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other lateral applications. The holdown must be attached to the receiving member with 5/8" machine bolts. A minimum wood member thickness of 1-1/2" is required to reach the least allowable tension load. The bottom stud hole is 4-3/4" above the plate line so you can install the holdown flush with the plate...

Simpson Strong-Tie EPB44 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying...

Simpson Strong-Tie EPB44 allows you to install an elevated 4 x 4 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 4 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and un-braced carports. Finish: Simpson Gray Paint Pipe Size: 1-1/16" OD x 8" Length Base Size:...

The geometry of the Simpson Strong-Tie SB5/8x24HDG Hot Dipped Galvanized 5/8" x 24" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions...

The geometry of the Simpson Strong-Tie SB5/8x24HDG Hot Dipped Galvanized 5/8" x 24" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 6" wide concrete stem wall without creating excessive horizontal forces. The SB5/8x24 is designed to maximize performance with minimum embedment of 18". Identification on the bolt head showing embedment angle and model Stamped embedment line...

Simpson Strong-Tie HTU26-2 Double 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26-2 hanger very versatile for...

Simpson Strong-Tie HTU26-2 Double 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26-2 hanger very versatile for various trusses. Additionally you can have the HTU26-2 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is...

Simpson Strong-Tie AT-XP13 Fast-Curing Anchoring Adhesive for Cracked and Uncracked Concrete dispenses easily in cold or warm environments with little to no odor. When mixed properly through the...

Simpson Strong-Tie AT-XP13 Fast-Curing Anchoring Adhesive for Cracked and Uncracked Concrete dispenses easily in cold or warm environments with little to no odor. When mixed properly through the included nozzle AT-XP13 is a teal color for easy post-installation identification when required. AT-XP13 anchoring adhesive has demonstrated superior performance in reduced-temperature testing (14°F) and is made in the USA. AT-XP adhesive has passed the demanding adverse condition tests of ICC-ES...

The Simpson Strong-Tie SUR24 Skewed Right 2 x 4 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists...

The Simpson Strong-Tie SUR24 Skewed Right 2 x 4 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 4 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/2" (Height) x 1-1/8" (Outside Flange) x 1-1/4" (Inside Flange) Fastener Options : (4) .162" x 3-1/2" 16d Nails (Face) (4) .148" x 1-1/2"...

The Simpson Strong-Tie DSC2R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that...

The Simpson Strong-Tie DSC2R-SDS3 Right Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. Material: 7 gauge Finish: Standard G90 Galvanized Dimensions: 16" (Length) x 3" (Flanges) Included Fasteners: (20) SDS 1/4" x 3" DSC2R-SDS3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...

Simpson Strong-Tie GBC Gable Brace Connector provides improved anchorage of gable bracing to the exterior wall. Installation flexibility for brace angle. GBC has tension and compression capacities....

Simpson Strong-Tie GBC Gable Brace Connector provides improved anchorage of gable bracing to the exterior wall. Installation flexibility for brace angle. GBC has tension and compression capacities. GBC clips must be installed in pairs to reach full load capacity. Material: 16 Gauge Finish: Standard G90 Zinc Installation Angles: 40° to 60° Fasteners-Gable Brace: (5) 8d x 1-1/2" Nails Fasteners-Top Plates: (7) 8d Nails GBC Information and Installation Instructions. Standard G90 Zinc...

Simpson Strong-Tie ST12 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications....

Simpson Strong-Tie ST12 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 11-5/8" (Length) Fastener Options: (10) 16d Nails (10) SD10 x 1-1/2" Screws ST12 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains...