Login/Register
Shopping Cart
OR
The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move...
The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...
The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...
The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...
The Simpson Strong-Tie DSC2L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are...
The Simpson Strong-Tie DSC2L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. Material: 7 gauge Finish: Standard G90 Galvanized Dimensions: 16" (Length) x 3" (Flanges) Included Fasteners: (20) SDS 1/4" x 3" DSC2L-SDS3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...
The Simpson Strong-Tie SUL24 Skewed Left 2 x 4 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists...
The Simpson Strong-Tie SUL24 Skewed Left 2 x 4 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 4 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/2" (Height) x 1-1/8" (Outside Flange) x 1-1/4" (Inside Flange) Fastener Options : (4) .162 x 3-1/2" 16d Nails (Face) (4) .148 x 1-1/2" 10d...
The Simpson Strong-Tie HDQ8-SDS3 holdown combines low deflection and high loads with ease of installation. The unique seat design of the HDQ8 greatly minimizes deflection under load. (20) 3" SDS...
The Simpson Strong-Tie HDQ8-SDS3 holdown combines low deflection and high loads with ease of installation. The unique seat design of the HDQ8 greatly minimizes deflection under load. (20) 3" SDS Simpson Strong-Tie® Strong-Drive® screws are included which install easily, reduces fastener slip and provide a greater net section area of the post when compared to bolts. They may be installed either flush or raised off the mudsill without a reduction in load value. Material: 7 Gauge Steel...
The Simpson Strong-Tie® Strong-Drive® SDWS22300DB .220" x 3" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects...
The Simpson Strong-Tie® Strong-Drive® SDWS22300DB .220" x 3" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects where a high-strength attachment is needed. The 0.220" diameter of the SDWS22300DB 3" wood screw requires less torque to install than comparable fasteners, making it easier to drive. The Double-Barrier Coating corrosion-resistant coating makes it suitable for many interior and exterior applications....
Simpson Strong-Tie HTU26 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26 hanger very versatile for various...
Simpson Strong-Tie HTU26 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26 hanger very versatile for various trusses. Additionally you can have the HTU26 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is 1/8" per ASTM...
The Simpson Strong-Tie® Strong-Drive® SDWH19300DB 3" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter...
The Simpson Strong-Tie® Strong-Drive® SDWH19300DB 3" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter fastener requires less torque to install than comparable fasteners, making it easier to drive; while the corrosion-resistant coating makes it suitable for many interior and exterior applications. The large hex washer head of the SDWH19300DB 3" screw creates an excellent bearing area for a secure...
The geometry of the Simpson Strong-Tie SB5/8x24 5/8" x 24" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor...
The geometry of the Simpson Strong-Tie SB5/8x24 5/8" x 24" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 6" wide concrete stem wall without creating excessive horizontal forces. The SB5/8x24 is designed to maximize performance with minimum embedment of 18". Identification on the bolt head showing embedment angle and model Stamped embedment line Rolled thread for higher...
Simpson Strong-Tie MASA anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASA is not only quick to install they also eliminate the...
Simpson Strong-Tie MASA anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASA is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASA version is used for installation on standards forms. Attaches easily to the concrete form for quick installation Lays flat on the form board so there is no anchor bolt to finish around No labor costs involved in drilling plates and...
Simpson Strong-Tie PBS44AZ Standoff Post Bases are used to connect a 4 x 4 (3-1/2" x 3-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay...
Simpson Strong-Tie PBS44AZ Standoff Post Bases are used to connect a 4 x 4 (3-1/2" x 3-1/2") to a concrete slab. The 1" standoff keeps the post off the concrete which reduces the chance of decay over time. ZMax® coating provides additional protection from the weather elements. Finish: ZMax® Base Material: 12 Gauge Base Dimensions: 3-9/16" x 3-1/2" Strap Material: 14 Gauge Strap Height: 6-1/4" Fastener Options: (14) 16d (2) 1/2" Machine Bolts Additional PBS44AZ information and...
Simpson Strong-Tie HD3B Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other lateral applications. The...
Simpson Strong-Tie HD3B Holdowns are a light duty bracket that is designed for a variety of uses including but not limited to shearwalls, braced-wall panels and other lateral applications. The holdown must be attached to the receiving member with 5/8" machine bolts. A minimum wood member thickness of 1-1/2" is required to reach the least allowable tension load. The bottom stud hole is 4-3/4" above the plate line so you can install the holdown flush with the plate without weakening the post or...
The Simpson Strong-Tie ABW44Z for 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete...
The Simpson Strong-Tie ABW44Z for 4x4 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW44Z allows...
The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD9112 #9 x 1-1/2"...
The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD9112 #9 x 1-1/2" structural connector screws are approved to replace nails in certain Simpson Strong-Tie Connectors. The advantages of using screws can be ease of installation in tight spots and less vibration when installing connectors during remodel projects. The shank of the SD9112 screws are designed to easily fit in...
With the Simpson Strong-Tie SDWC15450-KT 4-1/2" Structural Screws you will now have the flexibility to provide an approved connection even after the exterior shear wall has been installed. The labor...
With the Simpson Strong-Tie SDWC15450-KT 4-1/2" Structural Screws you will now have the flexibility to provide an approved connection even after the exterior shear wall has been installed. The labor savings installing the SDWC15450-KT 4-1/2" Structural Screws as opposed to installing traditional ties and straps will more than offset the costs of the fasteners. The 6-lobe drive using a T-30 bit reduces your chance of stripping out the screw, enabling a quick and secure installation. Fully...
The S/HDU4 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU4 holdown...
The S/HDU4 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU4 holdown combines performance with ease of installation using #14 screws self-drilling tapping screws thus saving time and labor.. The pre-deflected geometry virtually eliminates material stretch, resulting in low deflection under load. Foundation Anchor Diameter: 5/8" Fasteners (Not Included): (6) #14 Screws...
The Simpson Strong-Tie EPC4Z post cap is designed with the post and beam flanges in-line so that the EPC4Z end post cap can accommodate several 4x post sizes as well as double 2x4 studs. The EPC4Z...
The Simpson Strong-Tie EPC4Z post cap is designed with the post and beam flanges in-line so that the EPC4Z end post cap can accommodate several 4x post sizes as well as double 2x4 studs. The EPC4Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Please Note: This cap may be special ordered in a rough...
The Simpson Strong-Tie CPT44Z concealed 4 x 4 post base provides a clean, concealed look while providing a 1" standoff height above concrete. The 1" standoff reduces the potential for decay at the...
The Simpson Strong-Tie CPT44Z concealed 4 x 4 post base provides a clean, concealed look while providing a 1" standoff height above concrete. The 1" standoff reduces the potential for decay at the post end and satisfies code requirements for posts that are exposed to weather, water splash or in basements. Each base includes (3) 1/2" x 2-3/4" mechanical galvanized dowels. If 1/2" machine bolts are substituted it is recommended they are hot dipped galvanized. The CPT44Z is tested and load-rated...
Simpson Strong Tie face mount HU1.81/5 Composite Lumber Hanger is designed for hanging 1-3/4" x 5-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load...
Simpson Strong Tie face mount HU1.81/5 Composite Lumber Hanger is designed for hanging 1-3/4" x 5-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 5-3/8" (Height) x 2-1/2" (Seat Depth) Fastener Options: (12) 16d Nails (Header-Min) (4) 10d Nails (Joist-Min) (16) 16d Nails (Header-Max) (6) 10d Nails (Joist-Max) HU1.81/5 Information and Installation...
Bright Checkered Nail Head The Simpson Strong-Tie S13A225SNC 2-1/4" x .092" Non-Painted Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in...
Bright Checkered Nail Head The Simpson Strong-Tie S13A225SNC 2-1/4" x .092" Non-Painted Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in fine wood siding from hard-to-remove stains and streaks with stainless steel wire coil nails. Chose from four colors or unpainted to match your siding. 3,600 nails per box Head Color - Bright Type 304 stainless steel 15° collated angle Checker pattern on heads blends with wood grain, reduces...
The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie...
The Simpson Strong-Tie DTT1Z Deck Tension Tie provides a less invasive approach for attaching a new deck to a home or retrofitting an existing deck to current code standards. This tension tie addresses a 2015 International Residential Code provision (section R507.2.4) that now allows four 750 lb. lateral connectors to be fastened to framing in the house with a lag screw. This provision is an alternative to using two 1,500 lb. lateral connections from the deck to the floor joists within the...
The Simpson Strong-Tie CBT2Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether...
The Simpson Strong-Tie CBT2Z Concealed Beam Tie combines structural strength with invisibility for applications that call for concealed joinery rather than standard beam-to-post connections. Whether you’re designing for a custom indoor or outdoor living space, the tubular shape of the CBTZ allows an easy-to-install beam-to-post connection using common tools. The CBT2Z is designed to connect beams and posts of a variety of sizes. The CBT2Z accommodates a minimum 4x4 post and 4x6 beam using four...
Simpson Strong Tie HUCQ1.81/9-SDS 1-3/4" Wide x 9" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/9-SDS hangers with concealed...
Simpson Strong Tie HUCQ1.81/9-SDS 1-3/4" Wide x 9" Heavy Duty Composite Lumber Hangers come with the required SDS screws to reach the load values you require. HUCQ1.81/9-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-3/4" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (8) SDS 1/4" x 1-3/4" Screws (Header) (4) SDS 1/4" x 1-3/4" Screws...
The Quik Drive® PRO300SM35K Auto-Feed Screw Driving tool is the ideal tool for installing Quik Drive® Screws up to 3" in plywood subfloor, 2x Decking and more. The Sure-Grip guide tube...
The Quik Drive® PRO300SM35K Auto-Feed Screw Driving tool is the ideal tool for installing Quik Drive® Screws up to 3" in plywood subfloor, 2x Decking and more. The Sure-Grip guide tube increases the stability of the PRO300SM35K for a wide range of screws. The decking nose clip positions the screw on the deck board and centers it on the joist for an easy, uniform installation from a standing position. Kit Includes (1 Each): Makita 3500 RPM Screwdriver, PRO300S Attachment, Extension for...