Simpson Strong-Tie

The Simpson Strong-Tie H1 Hurricane and Seismic Ties are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Save when purchasing by the box of 100 pieces. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1 Information and Installation Instructions. Standard G90 Zinc Galvanized...

The Simpson Strong-Tie HGA10 Gusset Angle w/SDS Screws attaches to the top plate and gable trusses or rim joist to provides good lateral (cross) wind resistance. Save by purchasing by the box of 10 HGA10 angles. Includes: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws Material: 14 Gauge Finish: Standard G90 Zinc Fastener Included: (4) 1/4" x 1-1/2" SDS Screws and (4) 1/4" x 3" SDS Screws HGA10 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...

Simpson Strong Tie HU26 2 x 4/6 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-9/16" (Wide) x 3-1/16" (Height) x 2-1/4" (Seat Depth) Fasteners: (4) 16d Nails (2) 10d x 1-1/2" Nails (Joist) HU26 Information and Installation Instructions. Standard G90...

Simpson Strong Tie U24 2 x 4 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/8" (Height) x 1-1/2" (Seat Depth) Fastener Options: (4) 10d Nails (Header - Min) (4) 16d Nails (Header - Max) (2) 10d x 1-1/2" Nails (Joist) U24 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...

Simpson Strong Tie HUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS26 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 5-3/8" (Height) x 3" (Seat Depth)...

Simpson Strong Tie HGUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 5-3/8" (Height) x 5" (Seat Depth) Fastener Options: (20) 16d Nails (Header) (8) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS26 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...

The Simpson Strong-Tie CJT3S is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT3S short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 6 Glulam Beam - 3-1/8" x 7-1/2" PSL - 3-1/2 x...

Simpson Strong-Tie CMST12 Coil Strap allows you to install 3" wide strapping at various lengths depending on your span requirements. CMST12 are approved for use with SD Screws as a nail substitution. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3" (Wide) x 40' (Length) Fasteners: 10d or 16d depending on end length and material (See information link below) CMST12 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc...

Simpson Strong-Tie LSTA9 20 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a LSTA strap that requires bending the strap can only be bent one time. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 9" (Length) Fasteners: (8) 10d Nails (8) SD9 x 1-1/2" Screws LSTA9...

Simpson Strong-Tie MSTA9 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 9" (Length) Fasteners: (8) 10d Nails (8) SD9 x 1-1/2" Screws MSTA9...

The Simpson Strong-Tie STC Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The STC has a single 1-1/2" slot that will permit the truss chord to move vertically when loads are applied to the roof. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (3) 8d Nails STC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area...

Simpson Strong-Tie ST9 16 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 9" (Length) Fastener Options: (8) 16d Nails (8) SD10 x 1-1/2" Screws ST9 Information and Installation Instructions. Please Note: If there are any items on the Simpson website that you do not see on the DHC Supplies...

Simpson Strong-Tie ECCLL666 End Corner Column Caps provide a left connection between (2) 6x beams and (1) 6 x 6 posts when both beams end at the post. Material: 7 gauge Finish: Simpson Gray Paint Dimensions: 5-1/2" (Beams) x 5-1/2" (Posts) Fasteners: (6) 5/8" x 7" Machine Bolt (Beam & Post) ECCLL666 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint intended to only protect the product while it is being warehoused and...

Simpson Strong-Tie GBC Gable Brace Connector provides improved anchorage of gable bracing to the exterior wall. Installation flexibility for brace angle. GBC has tension and compression capacities. GBC clips must be installed in pairs to reach full load capacity. Save on GBC clips when purchased by the box of 25 pieces. Material: 16 Gauge Finish: Standard G90 Zinc Installation Angles: 40° to 60° Fasteners-Gable Brace: (5) 8d x 1-1/2" Nails Fasteners-Top Plates: (7) 8d Nails GBC...

The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie SUL24 Skewed Left 2 x 4 joist hangers are skewed 45 degrees left. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 4 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/2" (Height) x 1-1/8" (Outside Flange) x 1-1/4" (Inside Flange) Fastener Options : (4) 16d Nails (Face) (4) 10d x 1-1/2" Nails (Joist)...

The DSC2L-SDS3 Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. Material: 7 gauge Finish: Standard G90 Galvanized-Level of Corrosion Resistance: Low Dimensions: 16" (Length) x 3" (Flanges) Included Fasteners: (20) SDS 1/4" x 3" DSC2L-SDS3 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc...

Simpson Strong-Tie TA9Z-R Staircase Angles are used for securely providing support for stair treads eliminating the need for labor intensive notching of the stringer. The TA9Z angles are easily installed with (5) SDS25112 (1/4" x 1-1/2") screws or longer. Finish: ZMax® coating Material: 12 Gauge Fasteners: SDS25112 Screws - (3) Stringer, (2) Tread Dimensions: 8-1/4" Length x 1-1/2" (Flange Width) TA9Z-R Information & Installation Instructions ZMax® Galvanized Coating Information...

The Simpson Strong-Tie HDQ8-SDS3 holdown combines low deflection and high loads with ease of installation. The unique seat design of the HDQ8 greatly minimizes deflection under load. (20) 3" SDS Simpson Strong-Tie® Strong-Drive® screws are included which install easily, reduces fastener slip and provide a greater net section area of the post when compared to bolts. They may be installed either flush or raised off the mudsill without a reduction in load value. Material: 7 Gauge Steel...

Simpson Strong-Tie AT-XP13 Fast-Curing Anchoring Adhesive for Cracked and Uncracked Concrete dispenses easily in cold or warm environments with little to no odor. When mixed properly through the included nozzle AT-XP13 is a teal color for easy post-installation identification when required. AT-XP13 anchoring adhesive has demonstrated superior performance in reduced-temperature testing (14°F) and is made in the USA. AT-XP adhesive has passed the demanding adverse condition tests of ICC-ES...

The Simpson Strong-Tie® Strong-Drive® SDWS22300DB .220" x 3" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects where a high-strength attachment is needed. The 0.220" diameter of the SDWS22300DB 3" wood screw requires less torque to install than comparable fasteners, making it easier to drive. The corrosion-resistant coating makes it suitable for many interior and exterior applications. The low profile design of...

The Simpson Strong-Tie® Strong-Drive® SDWH19300DB 3" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter fastener requires less torque to install than comparable fasteners, making it easier to drive; while the corrosion-resistant coating makes it suitable for many interior and exterior applications. The large hex washer head of the SDWH19300DB 3" screw creates an excellent bearing area for a secure...

Simpson Strong-Tie HTU26 2 x 6 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU26 hanger very versatile for various trusses. Additionally you can have the HTU26 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is 1/8" per ASTM...

Simpson Strong-Tie LSU26 is a both a field slopeable and skewable hanger used to attached 2 x 6 joists or rafter to a header. This hanger can be either sloped up or down as well as skewed up to 45 degrees left or right. Because LSU26 hangers have a closed back they must be installed on the header or the end of the joist first. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 4-7/8" (Height) x 1-1/2" (Flange) Fastener Options : (6) 10d Nails (Face) (5) 10d x...

The geometry of the SB5/8x24 5/8" x 24" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 6" wide concrete stem wall without creating excessive horizontal forces. The SB5/8x24 is designed to maximize performance with minimum embedment of 18". Identification on the bolt head showing embedment angle and model Stamped embedment line Rolled thread for higher tensile capacity...

The Simpson Strong-Tie H1 Seismic and Hurricane Ties are designed to provide a secure connection between a 2x rafter and the double top plate at the point where the rafter rests on the plate. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners - To Rafter: (6) 8d x 1-1/2" Nails or SD9 x 1-1/2" Screws Fasteners - To Double Top Plate: (4) 8d Nails or SD9 x 1-1/2" Screws H1 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

The Simpson PB44 Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Nails Additional information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides)....

Simpson SET-XP Epoxy Tie can be used in both cracked and solid concrete when anchoring various structural anchors. The teal color shows inspectors and other interested parties that you are using the proper adhesive. SET-XP® adhesive has been rigorously tested in accordance with ICC-ES AC308 and 2006 IBC requirements and has proven to offer increased reliability in the most adverse conditions, including performance in cracked concrete under static and seismic loading. This SET-XP is a...

Simpson Strong-Tie HDU2-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (6) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 14 Gauge Steel Finish: Standard G90 Galvanized Anchor Bolt Diameter: 5/8" Pre-deflected...

Simpson Strong-Tie SET22-N High Strength Epoxy Tie with Nozzle is ideal for non-structural bonding such as rebar doweling, paste over crack injection and more. When the resin and hardener are mixed properly through the EMN22i mixing nozzle it produces a uniform light gray adhesive. SET meets or exceeds the ASTM C-881 specification for Type I, II, IV and V, Grade 3, Class B and C. Uses: Threaded rod anchoring Rebar dowelling Bonding hardened concrete to hardened concrete Pick proof sealant...

The Simpson CBSQ44-SDS2 (for 3-1/2" x 3-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 4 x 4 Nominal (3-1/2" x 3-1/2") Base: 12 Ga. (3-9/16" x 3-1/2") Strap: 10 Ga. x 2-1/4" Wide x 8-3/8" High CBSQ44 Information and Installation...

The Simpson Strong-Drive SDS25112 1/4" x 1-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25112 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Thread Length: 1" The patented 4CUT tip has a square core and serrated threads to reduce installation torque...