Login/Register
Shopping Cart
OR
Filter
Sort By
These 1/2" x 10" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length...
These 1/2" x 10" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of Corrosion...
These 1/2" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 1/2" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...
3/4" - 10 Hot Dipped Galvanized Hex Nuts for either 3/4" HDG machine bolts or all thread rod. Uses 1-1/8" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or...
3/4" - 10 Hot Dipped Galvanized Hex Nuts for either 3/4" HDG machine bolts or all thread rod. Uses 1-1/8" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or threaded rod. Do NOT use on plain or zinc plated bolts. Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating weight is 2.0 oz./ft2 (per ASTM A123 total both sides)....
3/4" Plain Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads and nuts from...
3/4" Plain Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads and nuts from pulling into the wood. These washers are not coated with any corrosion resistance material and will quickly rust if exposed to the elements. Bolt Hole Size: 13/16" Approximate Outside Diameter: 2-15/16" Approximate Washer Thickness: 3/8" Coating: None Explanation of "Stock" Availability Term Stock...
3/4" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and...
3/4" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and should not be used with ACQ lumber. Bolt Size: 3/4" Inside Diameter: 13/16" Outside Diameter: 2" Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...
BP58-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot...
BP58-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 11/16" Dimension: 2" x 2" Thickness: 3/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Hot Dipped Galvanized...
These 5/8" x 12" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as...
These 5/8" x 12" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...
These 1/2" x 12" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length...
These 1/2" x 12" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of Corrosion...
3/4" Hot Dipped Galvanized Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads...
3/4" Hot Dipped Galvanized Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads and nuts from pulling into the wood. These washers are hot dipped galvanized providing corrosion protection when required. Bolt Hole Size: 13/16" Approximate Outside Diameter: 2-15/16" Approximate Washer Thickness: 3/8" Coating: Hot Dipped Galvanized Hot Dipped Galvanized Coating Information Hot-Dip...
3/4" USS Hot Dipped Galvanized Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Hot Dipped Galvanizing provides corrosion...
3/4" USS Hot Dipped Galvanized Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Hot Dipped Galvanizing provides corrosion resistance to allow you to these washers with ACQ lumber. Bolt Size: 3/4" Inside Diameter: 13/16" Outside Diameter: 2" Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average...
BP58-3 Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates have no corrosion resistance and...
BP58-3 Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates have no corrosion resistance and should not be used with ACQ lumber. Hole Size: 11/16" Dimension: 3" x 3" Thickness: 1/4" Coating: None Mild Steel Imported Picture may not match product exactly Explanation of "Stock" Availability Term Stock items are products we normally have available for immediate shipment either from our...
These 5/8" x 24" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated...
These 5/8" x 24" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments....
7/8" x 2-1/2" (H) Witness Hole Coupling Nuts are used to connected two 7/8" threaded rods together or extend a 7/8" SSTB or standard anchor bolt. The witness hole allows the inspector to confirm the...
7/8" x 2-1/2" (H) Witness Hole Coupling Nuts are used to connected two 7/8" threaded rods together or extend a 7/8" SSTB or standard anchor bolt. The witness hole allows the inspector to confirm the rods are connected properly. Zinc Plated Hex Head Imported Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used...
These 1/2" x 10" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 1/2" x 10" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...
BP58-3HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot...
BP58-3HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 11/16" Dimension: 3" x 3" Thickness: 1/4" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Hot Dipped Galvanized...
These 5/8" x 24" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as...
These 5/8" x 24" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...